manualshive.com logo in svg

E-FLITE Beechcraft Bonanza 15e ARF, Assembly Manual

The E-FLITE Beechcraft Bonanza 15e ARF is an exceptional model airplane that delivers unparalleled flying experiences. Assembling this high-quality aircraft is a breeze with the comprehensive Assembly Manual, which you can easily download for free from our website. Dive into the world of thrilling flights with this remarkable Bonanza model!

Share
Download
background image

22

Beechcraft Bonanza 15e ARF Assembly Manual

□□ 

Step 10

Set the servo in place between the mounting blocks 

and use a pencil to mark the mounting hole locations.

Note:

 It may be necessary to carve a relief in one of 

the blocks to provide clearance for the servo lead. Use 

a hobby knife to do so if required.

□□ 

Step 11

Remove the servo. Use a 1/16-inch drill bit in a pin 

vise to drill the servo mounting holes.

□□ 

Step 12

Apply a drop of thin CA to each of the mounting 

holes to strengthen the wood. Allow the CA to cure 

completely without using accelerator.

□□ 

Step 13

Use a #1 Phillips screwdriver and the screws

provided with the servo to install the servo to the 

aileron hatch.

□□ 

Step 14

Connect a 9-inch servo extension lead to the aileron 

servo. Use dental floss to secure the connectors.

Summary of Contents for Beechcraft Bonanza 15e ARF





























































Reviews:

No comments

Related manuals for Beechcraft Bonanza 15e ARF

Faller 388 Manual preview
388
Brand: Faller Pages: 12
Fei Bao Velox Assembly Manual preview
Velox
Brand: Fei Bao Pages: 64
LGB 27254 Manual preview
27254
Brand: LGB Pages: 37
PARKZONE Radian RTF Instruction Manual preview
Radian RTF
Brand: PARKZONE Pages: 10
PARKZONE Focke-Wulf 190 RTF Instruction Manual preview
Focke-Wulf 190 RTF
Brand: PARKZONE Pages: 56
GREAT PLANES Viper 500 RTC Instruction Manual Supplement preview
Viper 500 RTC
Brand: GREAT PLANES Pages: 4
Power Wheels Kawasaki KFX P9723 Owner'S Manual & Assembly Instructions preview
Kawasaki KFX P9723
Brand: Power Wheels Pages: 25
South Coast Sailplanes Voltij Manual preview
Voltij
Brand: South Coast Sailplanes Pages: 9
LEGO Sopwith camel 3451 Instructions Manual preview
Sopwith camel 3451
Brand: LEGO Pages: 52
K'Nex MARIO KART WII MARIO AND YOSHI FINISH LINE BUILDING SET Manual preview
MARIO KART WII MARIO AND YOSHI FINISH LINE BUILDING SET
Brand: K'Nex Pages: 12
ProBoat PRB08028V2 Owner'S Manual preview
PRB08028V2
Brand: ProBoat Pages: 19
Sago TOCA LIFE BOX SUSHI STATIONERY Quick Start Manual preview
TOCA LIFE BOX SUSHI STATIONERY
Brand: Sago Pages: 6
Tamiya BOEING F-15E STRIKE EAGLE W/BUNKER BUSTER Manual preview
BOEING F-15E STRIKE EAGLE W/BUNKER BUSTER
Brand: Tamiya Pages: 29
Fisher-Price 71933 Instructions preview
71933
Brand: Fisher-Price Pages: 4
VTech Baby Toot-Toot Drivers Service Centre Play set User Manual preview
Toot-Toot Drivers Service Centre Play set
Brand: VTech Baby Pages: 11
VTech Baby Shake & Sounds Caterpillar Parents' Manual preview
Shake & Sounds Caterpillar
Brand: VTech Baby Pages: 12
marklin BR VT 11.5 Manual preview
BR VT 11.5
Brand: marklin Pages: 56
Hobbytrain E-Lok E17 Manual preview
E-Lok E17
Brand: Hobbytrain Pages: 4

Brands by name

Popular brands

Load more brands