E-FLITE Beechcraft Bonanza 15e ARF Assembly Manual Download Page 4

Page: 4 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Rudder and Elevator Servo and Pushrod

Installation

Parts Required

Fuselage

Micro servos (2)

Clevis (2)

Silicone keeper (2)

Snap keeper (2)

Radio

16 1/2-inch steel pushrod (2)

Tools Required

Pin vise

1/16-inch drill bit

5/64-inch drill bit

Pencil

Sidecutters

Pliers

Hobby knife

Ruler

Razor saw

Thin CA

#1 Phillips screwdriver

Note:

go to Page 11 if installing the optional V-tail.

□

Step 1

Remove the canopy by pushing it forward from the

rear edge to disengage the magnets, then lifting and

pulling aft.

□□

Step 2

Install the grommets and bushings in the rudder and

elevator servos. Note that the bushing is installed

from the bottom of the servo.

□□

Step 3

Use a #1 Phillips screwdriver to remove the small

servo arm and install a standard 4-way arm on each

servo.

□□

Step 4

Use sidecutters to remove three of the servo arms,

leaving one long arm on opposite sides of each

servo.

□

Step 5

Use a hobby knife with a #11 blade to remove the

covering from the rudder pushrod exit on the right

side of the rear fuselage.

Summary of Contents for Beechcraft Bonanza 15e ARF





























































Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands

E-FLITE Beechcraft Bonanza 15e ARF, Assembly Manual

Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands