background image

SPECIFICATIONS

Wingspan:......................................1730mm 
Length (installed motor) .................1190mm 
Electric Motor:.................................800Watt
Glow Engine:....................  .55 2-T / .72 4-T

Radio:....................6 Channel / 6-7 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps.

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Radio control model / Flugmodel

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

 

Instruction manual / Montageanleitung

VQ No: VQA160OL (U,S,ARMY)

RTF Weight: 3100 - 3450g (will vary with 
equipment use).

VQ No: VQA160G (U.S.AIR FORCE)

1730mm Wingspan

Summary of Contents for L-19/0-1 BIRD DOG 1730mm Wingspan

































Reviews: