background image

Installation, Operation and Service Manual 

 

LKP Series 

 

 

 

© 2016 DynAmp, LLC       

                       

Page iii 

041738 I

 

 DynAmp, LLC WARRANTY 

Items and components manufactured by Seller for permanent installation are warranted for 
two (2) years from the date of shipment.   

Items and components manufactured by Seller for portable and temporary use in more 
than one location are warranted to be free from defects in material and workmanship for a 
period of eighteen (18) months from the date of shipment. 

Items and components not manufactured and resold by Seller are warranted by their 
manufacturer. 

Warranty repair shall be, at DynAmp’s option, in the form of repair or replacement of the 
defective items or components.  Concerning warranty repairs, DynAmp will be responsible 
for DynAmp provided time, material and transportation costs (shipping or travel).  Actual 
method of warranty repair / correction will be determined by DynAmp at DynAmp’s sole 
option.  Such warranty repair shall constitute a fulfillment of all DynAmp, LLC liabilities in 
respect to said items and components.  In no event shall DynAmp, LLC be liable for 
consequential damages. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Information in this document is subject to change without notice. 
 
© 1997, 1998, 2000, 2002, 2003, 2004, 2006, 2008, 2011, 2016 DynAmp, LLC.  All rights reserved. 
 
Reproduction for purposes other than operation and service without written permission of DynAmp, 
LLC is strictly forbidden. 
 
This manual includes detailed drawings, installation, operation, service and maintenance.  Users 
should evaluate the information in the manual and their particular application.  DynAmp assumes no 
liability for any incidental, indirect, or consequential damages arising fro the use of this documentation. 
 
While all information presented is believed to be reliable and in accordance with accepted engineering 
practices, DynAmp makes no warranties as to the completeness of the information. 

 

 

Summary of Contents for LKP-100


















































Reviews: