background image

5

•  This ride-on toy has no brake; to stop take foot off foot pedal. Do no park or ride 

on any slopes or steep inclines.

•  Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in 

contact with wheels or other moving parts.

•  Before each cycle of operation, you must perform the preoperation checks 

specified in this manual or by the manufacturer, including:

 

– That all guards and pads originally supplied by the manufacturer are in proper 

place and in serviceable condition;

 

– That the area that the unit is to be operated in is safe and suitable for safe 

operation; and

 

– That all safety labels are in place and understood by everyone, including the 

riders.

•  Avoid sharp bumps, drainage grates, and sudden surface changes.
•  Do not ride in the rain or on wet surfaces.

PRE-RIDE SAFETY CHECKLIST

•  Check to make sure that all components are properly secured and are 

functioning according to the manufacturer’s specifications.

•  Components must be maintained and repaired and only with the manufacturer's 

authorized replacement parts. Installation should be performed only by adult, 
qualified personnel.

USING THE CHARGER

The charger should be examined regularly for damage to the cord, plug, enclosure 
and other parts. In the event such damage has occurred, the electric ride-on toy 
should not be charged until the charger has been repaired by qualified personnel 
or replaced. Use only the supplied, recommended charger.
•  Always use caution when charging.
•  The charger is not a toy and should be operated by an adult.
•  Never operate the charger near flammable materials or liquids, and operate the 

charger in well-ventilated areas.

•  Disconnect the charger and unplug it from the electric ride-on toy when not in 

use.

•  Do not exceed the recommended charging time.
•  Always disconnect the charger from the electric ride-on toy prior to wiping down 

or cleaning the electric ride-on toy with any liquid.

 WARNING: 

Never modify or alter the electrical system. Risk of fire. Do not bypass 

the fuse. Replace only with 3A fuse, located under the pedal. Alterations could cause a fire or 

explosion resulting in serious injury or death and could also ruin the electrical system.
FAILURE TO HEED THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIALLY SERIOUS 
INJURY. USE THE APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR APPROPRIATE 
CLOTHING AND SHOES.

Summary of Contents for 24V PRINCESS CARRIAGE



































Reviews: