Dynacraft 24V PRINCESS CARRIAGE Owner'S Manual Download Page 32

Page: 32 / 34

Problem

Possible Cause

Solution

Ride-on toy runs

sluggishly

Undercharged battery

Charge the battery. A new battery should have

been charged for at least 18 hours before using

the ride-on toy for the first time. After first-time

use, recharge the battery for at least 12 hours

after each use. Never charge the battery longer

than 30 hours. Check all connectors.
Make sure the battery connector is tightly

plugged into the control module connector, and

that the charger is plugged into the wall outlet.
Make sure that there is power flow to the wall

outlet.

Battery needs

charging

Be sure to charge the battery after each use.

Ride-on toy is

overloaded

Make sure you do not overload the ride-on toy

by allowing more than two riders at one time,

exceeding the 130 Ib. maximum weight capacity,

or by towing objects behind the ride-on toy. If the

ride-on toy is overloaded, the thermal fuse may

“trip”, and automatically shut down operation

of the ride-on toy for approximately 2 minutes.

Correct the condition that lead to the overload

and adjust the driving conditions to prevent

repeated automatic shutdowns.

Driving conditions too

stressful

Use only on level ground.

Sometimes

the ride-on toy

doesn’t run, but

other times it

does

Loose wire or

connector

Check all wires around the motors and all

connectors to make sure they are tight.

The battery’s

thermal fuse

constantly

“trips”, but the

ride-on toy is

not overloaded

and the driving

conditions are

not severe

Damaged battery

Replace with new battery. Replace only with an

original 24V 7AH battery. Do not use non-original

substitute parts.

Charger gets

warm during use

It is normal for some

chargers to get warm

during use and is not

reason for concern
Some chargers do not

get warm during use

No action required.
If your charger does not get warm during use, it

does not mean that it is not working properly.

Battery makes

a sizzling or

gurgling noise

when charging

It is normal for some

batteries to make

noise and swell

slightly while charging

and is not reason for

concern

No action required.
If your battery does not make noise or swell

slightly while charging, it does not mean that it is

not working properly.

Summary of Contents for 24V PRINCESS CARRIAGE



































Search results

Summary of Contents for 24V PRINCESS CARRIAGE

Reviews:

Related manuals for 24V PRINCESS CARRIAGE

Brands by name

Popular brands

Dynacraft 24V PRINCESS CARRIAGE, Owner'S Manual

Search results

Summary of Contents for 24V PRINCESS CARRIAGE

Reviews:

Related manuals for 24V PRINCESS CARRIAGE

Brands by name

Popular brands