manualshive.com logo in svg

Dyacon MS-100, Quick Start Manual, Page: 17 / 22

Share
Download
Dyacon MS-100 Quick Start Manual Download Page 17

DYACON Quick-start Guide

DyaconLive

Pressing 

Select

 will enable configuration of DyaconLive settings.

>Update Rate: Off
 Test Connection

6.1.3 DyaconLive Report Interval

Press 

Select

 to edit the on/off status and set reporting interval.

Set Update Rate
10_

Use the ▲ (Up) and ▼ (Down) buttons to turn the feature on at the desired interval, 1, min, 2 
min, 5 min, 10 min, 15 min, 20 min, 30 min, or 1 hr. Longer intervals may be helpful at reducing
system power and data usage.

A 10 min interval is recommended.

Press 

Select

 to save.

6.1.4 DyaconLive Test

To initiate a test of the DyaconLive connection.

Use the ▲ (Up) and ▼ (Down) buttons to select the Test Connection option.

 Update Rate: Off
>Test Connection

Press 

Select.

The display will exit Setup mode and return to the home screen and show the progress of the test
packet transmission.

WiFi    UTC 17:33:51
Dyacon Connecting

WiFi    UTC 17:33:51
Dyacon Sending

WiFi    UTC 17:33:52
Dyacon Complete

An error message may show if the test is unsuccessful. Contact Dyacon if the error is not 
obvious.

Page 17/22

Summary of Contents for MS-100























Reviews:

No comments