manualshive.com logo in svg

DWT BWT PERMAQ Pico 10-90, Installation And Operating Manual

Share
Download
DWT BWT PERMAQ Pico 10-90 Installation And Operating Manual Download Page 40

8 | Maintenance and servicing

OPM BWT PERMAQ® Pico Rev. 2.0 EN

EN

40

ð

The device is ready for cleaning agent.

Dosage of chemical cleaning agent (liquid) Osmoclean C

Pico 10

Approx. 250 ml

Pico 20

Approx. 400 ml

Pico 30

Approx. 500 ml

Pico 40

Approx. 800 ml

Pico 50

Approx. 1000 ml

Pico 60

Approx. 1200 ml

Pico 70

Approx. 1300 ml

Pico 80

Approx. 1400 ml

Pico 90

Approx. 1500 ml

Table

 

7: Dosage of chemical cleaning agent

Performing chemical cleaning

To perform chemical cleaning, proceed as follows:

1) In the main menu, use the 

↓ arrow

 to select 

DISINFECTION int.

 and press the 

OK but-

ton

 to confirm.

2) Confirm the question 

agent filled in?

 using the 

OK

 button.

Disinf. / Clean.

agent filled in?

back

DISINFECTION int.

ð

The cleaning programme starts automatically.

3) During step 

S1 Charging

, open the ventilation valve until all the air has escaped from the

pump pressure tube and only water now escapes. Close the ventilation valve again. 

DISINFECTION int.

S1 Charging

Remain. time: [ _ _ : _ _ ] s

 ... 

OFF

INSPECTION MODE >

DISINFECTION int. >

DISINFECTION ext. >

ð

The cleaning programme continues automatically.

4) Once the cleaning programme is complete, use the pH test strips to check whether the

acidic cleaning agent has been completely flushed out of the system. After flushing, the pH
value should be within the neutral or slightly acidic range (pH 6 to pH 7). If the pH value is
still too low, restart the 

DISINFECTION int.

 programme.

5) Once the pH value is within the stipulated value range, reconnect the permeate connection

on the device to the permeate tank.

ð

Once the cleaning programme is complete, the device switches to the 

OFF

 state.

6) Restart the device.

ð

The device has been chemically cleaned.

8.5 Venting the high-pressure pump

Without sufficient ventilation, the chemical disinfectant or cleaning agent is not distributed
evenly throughout the system; instead, some of it remains in the filter cup. This reduces the ef-
fectiveness of the cleaning/disinfection. Therefore, particularly after replacing a filter and be-
fore starting cleaning/disinfection, you must vent the system.

Summary of Contents for BWT PERMAQ Pico 10-90

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands