manualshive.com logo in svg

DWT BWT PERMAQ Pico 10-90, Installation And Operating Manual

Share
Download
DWT BWT PERMAQ Pico 10-90 Installation And Operating Manual Download Page 18

4 | Transport and installation

OPM BWT PERMAQ® Pico Rev. 2.0 EN

EN

18

Protection-

equipment

according to

EN 1717

BWT

filter

BWT Duplex

softener

Consumer

BWT PERMAQ Pico Vario

reverse osmosis

Fig.

 

14: Sample installation of the BWT PERMAQ

®

 Pico Vario

4.5 Hydraulic connection

The device must be connected to the water supply network by an authorised and qualified
sanitary plumber. The local statutory installation and accident prevention regulations, general
standards and guidelines and the hygiene requirements and technical data must be complied
with.

Hydraulic connection of the device (not BWT PERMAQ® Pico Vario)

To establish the hydraulic connection of the device, proceed as follows.

ü

The installation of an upstream stop valve (not included in the delivery) is recommended.

1) Connect the softened water line to the feed water inlet.

2) Guide the permeate line to the outlet and flush thoroughly.
3) Connect the permeate line to the consumer (e.g. permeate tank).
4) Connect the concentrate line to the customer-supplied waste water connection with the

“free run-off” or to a salt water-resistant lifting unit. Prevent the hose from weaving.
A maximum connection height of 1.0

 

m and minimum slope of approx. 1.0% applies for the

correct connection of the concentrate line. 

NOTICE! The line must not be kinked or have

any other constrictions in its cross section.

Summary of Contents for BWT PERMAQ Pico 10-90

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands