DUROMAX XP13000HXT User Manual Download

Page: 18 / 82

Propane Regulator w/

Hose

Used to provide a regulated

propane supply to the propane

inlet.

Natural Gas Hose

Used to provide a natural gas

supply to the propane inlet.

PACKAGE CONTENTS

Your generator comes with the items listed below. Please check to see that all of the following
items are included with your generator:

●

Note: Actual tools may differ in appearance or design from the image shown.

Double-Sided

Screw Driver

Oil Funnel w/ Hose

Spanner

Spark Plug Wrench

Phillips and slot blade

screwdriver used for generator

maintenance.

Used to add oil to the

generator without messy spills.

Assorted wrenches used in

generator maintenance and

assembly. 10mm/12mm,

13mm/15mm, and

17mm/19mm.

Used in spark plug

maintenance, inspection, and

installation.

Summary of Contents for XP13000HXT



















































































Search results

Summary of Contents for XP13000HXT

Reviews:

Related manuals for XP13000HXT

Brands by name

Popular brands

DUROMAX XP13000HXT, User Manual

Search results

Summary of Contents for XP13000HXT

Reviews:

Related manuals for XP13000HXT

Brands by name

Popular brands