DUROMAX XP13000HXT User Manual Download | Manualshive

Page: 32 / 82

background image

STARTING THE GENERATOR

32

Turn breaker OFF

The breaker is located on the right side of the front power
panel. Flip the breaker down to prevent accidental load
when starting the generator.

1.

Turn gas type to gasoline

Turn fuel type to gasoline

The fuel switch is located on the left front panel. Rotate the
switch to the PROPANE/GASOLINE position to turn on the
gas supply.

The fuel switch is located on the left front panel. Rotate the
switch to the GASOLINE position to turn on the gas supply.

2.

4.

Turn battery switch ON

The battery switch is located on the top center of the main
power panel. Turn the switch ON to allow power to the
push-button start.

3.

Starting the Generator Using Gasoline

«
...
30
31
32
33
34
...
»

Summary of Contents for XP13000HXT



















































































Reviews:

No comments

Related manuals for XP13000HXT

Brand: CA Pages: 6

Brand: Southwest Windpower Pages: 42

Brand: Denver Pages: 60

Brand: P1PE Pages: 32

NS-HD01 - Portable HD Radio

Brand: Insignia Pages: 2

Brand: Hayter Pages: 52

Brand: Motorola Pages: 82

Brand: Motorola Pages: 34

Brand: Motorola Pages: 28

Brand: Motorola Pages: 526

Brand: Motorola Pages: 29

Brand: Mosa Pages: 38

Brand: artisan Pages: 89

Brand: Datalogic Pages: 28

Brand: Roadstar Pages: 28

Brand: Roadstar Pages: 32

Brand: Roadstar Pages: 42

Brand: Infinity Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands