DUROMAX XP13000HXT Page 36 User Manual Download | Manualshive

Page: 36 / 82

background image

STARTING THE GENERATOR (CONTINUED)

Starting the Generator Using Natural Gas

36

Turn breaker off

The breaker is located on the right side of the front power
panel. Flip the breaker down to prevent accidental load
when starting the generator.

1.

Turn gas type to natural gas

Connect hose

Turn fuel type to natural gas

The fuel switch is located on the left front panel. Rotate
the switch to the Natural Gas position to turn on the fuel
supply.

The quick connect inlet is located on the left-hand front
panel to the right of the fuel switch. Securely connect the
hose to the inlet.

The fuel switch is located on the left front panel. Rotate the
switch to the Natural Gas/Propane position to turn on the
fuel supply.

2.

3.

4.

«
...
34
35
36
37
38
...
»

Summary of Contents for XP13000HXT



















































































Reviews:

No comments

Related manuals for XP13000HXT

Brand: Saluki Pages: 42

Brand: Akai Pages: 2

Brand: ulsonix Pages: 4

PORTABLE GENERATORS

Brand: Gillette Pages: 6

Storm Responder 5500

Brand: Briggs & Stratton Pages: 48

Brand: LoadUP Pages: 60

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 47

Brand: Kenwood Pages: 60

Brand: Kenwood Pages: 10

Brand: Kenwood Pages: 33

Brand: Kenwood Pages: 73

Brand: Kenwood Pages: 70

Brand: Kenwood Pages: 62

Brand: Kenwood Pages: 66

Brand: AWA Pages: 25

Brand: GoVideo Pages: 1

Brand: GoVideo Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands