DUROMAX XP13000HXT User Manual Download

Page: 12 / 82

CARBON MONOXIDE SAFETY

Carbon Monoxide

CO Alert

●

The indicator will light red.

●

The engine will shutdown.

●

The engine will not restart for 5 minutes.

Maintenance Required

If an error in the CO Alert system is detected, the indicator
will light yellow. Please contact DuroMax Service at
844-DUROMAX for assistance.

Description

The DuroMax CO Alert system was created to protect

our customers and their families from dangerous carbon

monoxide. Just like the detector for your home, the CO Alert

tests the air for to keep you safe and healthy.

CO Detected

If dangerous carbon monoxide levels are detected:

Generators are very convenient, but they can also be very dangerous. All

fuel-burning appliances and equipment release a poisonous gas called

carbon monoxide.

Carbon monoxide (also known as CO) can be dangerous for humans

and pets, even in small amounts, because it blocks oxygen from getting

into your body. Carbon monoxide poisoning can lead to death in a very

short time. It is odorless, tasteless and invisible, so you may be exposed

without knowing it. That is why carbon monoxide is sometimes called

“the silent killer.”

Summary of Contents for XP13000HXT



















































































Search results

Summary of Contents for XP13000HXT

Reviews:

Related manuals for XP13000HXT

Brands by name

Popular brands

DUROMAX XP13000HXT, User Manual

Search results

Summary of Contents for XP13000HXT

Reviews:

Related manuals for XP13000HXT

Brands by name

Popular brands