Ducati SPORT 1000 S Page 80 Owner'S Manual Download | Manualshive

Page: 80 / 96

background image

79

E

Fuses

The main fusebox is located under the seat in the electrical
compartment (fig. 64).
The fuses are accessed by removing the cover (1), which
shows the ampere ratings and mounting locations.
There are 7 fuses in the electrical system and these are
located inside the fusebox.

The 30 A fuse (2) on the side of the fusebox (fig. 65) protects
the electronic voltage regulator.
To access this fuse, remove the protective cap (3).

A blown fuse can be identified by a broken filament (4, fig. 66).

Important

To avoid possible short circuits, switch the ignition

key to

OFF

before renewing the fuse.

Warning

Never use a fuse with a rating other than that specified.

Failure to observe this rule may damage the electric system
or even cause fire.

4

4

IN GOOD CONDITION

INTEGRO

BLOWN

QUEMADO

fig. 66

«
...
78
79
80
81
82
...
»

Summary of Contents for SPORT 1000 S

































































































Reviews:

No comments

Related manuals for SPORT 1000 S

Brand: LAZER Pages: 6

Brand: Racelogic Pages: 2

Brand: MOTO GUZZI Pages: 134

Brand: VESPA Pages: 46

Brand: R&G Pages: 2

Brand: R&G Pages: 9

Brand: R&G Pages: 4

Brand: R&G Pages: 6

Brand: Wunderlich Pages: 5

Brand: Ultra-tow Pages: 6

Brand: Benelli Pages: 32

Brand: Benelli Pages: 77

Brand: APRILIA Pages: 576

250 EXC-F EU 2010

Brand: KTM Pages: 136

Brand: KTM Pages: 100

Brand: Electronicbox Pages: 2

MP1 PROFESSIONAL

Brand: PAB Pages: 20

Brand: Rivco Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands