Ducati SPORT 1000 S Owner'S Manual Download Page 91 | Manualshive

Page: 91 / 96

Ducati SPORT 1000 S Owner'S Manual Download Page 91

90

E

US

A

C. No dealer is authorized to modify this Ducati Limited
Emission Control Systems Warranty.

IV. Legal rights

This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

V.

This warranty is in addition to the Ducati limited

motorcycle warranty.

VI. Additional information

Any replacement part that is equivalent in performance
and durability may be used in the performance of any
maintenance or repairs. However, Ducati is not liable for
these parts. The owner is responsible for the performance
of all required maintenance. Such maintenance may be
performed at a service establishment or by any individual.
The warranty period begins on the date the motorcycle is
delivered to an ultimate purchaser.

Ducati North America, Inc.
10443 Bandley Drive
Cupertino, California, 95014
Tel: 001.408.253.0499
Fax: 001.408.253.4099
E-mail: [email protected]
Web site: www.ducatiusa.com

«
...
89
90
91
92
93
...
»

Summary of Contents for SPORT 1000 S

































































































Reviews:

No comments