WFQT130005
11
V4.1B
STEP
5
(Optional Direct Connect)
Install the QuickTwist
®
Filter
1
Hold the QuickTwist® Filter with the label facing to the left slightly. The two nozzles on top of the QuickTwist® Filter should be
toward the back of the QuickTwist® Filter. If holding properly, the two extended flanges on top of the QuickTwist® Filter should be
out to each side. See Figure 5
at right.
2
Lift the QuickTwist® Filter straight up into the System Head
A
until the two nozzles seat into the ports and the two extended flanges
on top of the QuickTwist® Filter are fully engaged into the System Head.
3
Turn the QuickTwist® Filter from right to left until it stops.
STEP
6
(Optional Direct Connect)
Test the Filter System for Proper Operation
1
Turn on the cold water shut-off valve under the sink.
2
Turn on the new Faucet for Filtered Water
D.
In order for the Filter System to flush out any air and carbon fines (fine black powder)
from the QuickTwist® Filter, allow the water to run for approximately 10 minutes.
3
Check for any leaks between the System Head assembly and Filter; around all fittings; on Kitchen Faucet Adapter
H
connection; and
on faucet/tubing connection.
If there are leaks between the System Head Assembly and the QuickTwist
®
Filter:
n
Turn off the cold water shut-off valve to the Filter System and turn on the Faucet for Filtered Water to drain the water and release pressure.
n
Remove the QuickTwist® Filter and inspect the O-Rings around the nozzles on top of it. Make sure they are in place and free from dirt and particles.
n
Turn off the Faucet for Filtered Water.
n
Replace the QuickTwist® Filter by lifting it straight up into the System Head until the two nozzles seat into the ports and the two extended flanges on top of the QuickTwist® Filter are fully engaged into
the System Head. Turn the QuickTwist® Filter left to right until it stops.
n
Turn the cold water supply valve back on and turn on the Faucet for Filtered Water.
If there are leaks around the fittings:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n
While pulling the 1/4” Plastic Tubing
L
with one hand, press in on the grey collar around the inlet and/or outlet fitting. Check to make sure that the 1/4” Plastic Tubing is cut squarely and that it is not
scratched or crimped. If the 1/4” Plastic Tubing is unevenly cut or scratched, cut off 1/2” to 5/8” and re-install the Plastic Tubing (see Step 4 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
If there are leaks on the Kitchen Faucet Adapter connection:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n
Locate the Kitchen Faucet Adapter.
• If the 1/4” Plastic Tubing is leaking, follow the previous steps (“If there are leaks around the fittings”).
• If the thread between the Kitchen Faucet Adapter and the kitchen faucet stem is leaking, tighten more securely. If leaking continues, disconnect the 1/4” Plastic Tubing and remove the Kitchen Faucet
Adapter. Wrap the Kitchen Faucet Adapter and the threaded faucet stem with plumber’s tape and re-install (see Step 3 of Installation Instructions).
• If the thread between the Kitchen Faucet Adapter and the cold water supply line is leaking, tighten more securely. If leaking continues, disconnect the 1/4” Plastic Tubing and remove the Kitchen Faucet
Adapter. Wrap the Kitchen Faucet Adapter and the cold water supply line with plumber’s tape and re-install (see Step 3 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
n
If leaks continue, turn off the water supply and call Customer Service.
n
For Filter Replacement Instructions, please see page 8.
X
X
WFQT130005
1
3
B
A
5
2
