DSC PC5008 Manual Download Page 2

2

This manual describes how to install, program and maintain the PC5132-RS.

Before you install the PC5132-RS module, you should have completed the
following steps in your system installation:

1. Plan the installation and wiring of the security system (see your system

Installation Manual)

2. Install the control panel, and install and enroll at least one keypad to use

for programming.

3. Install and enroll any hardwired zone expander modules (PC5108) you

plan to use.

NOTE: PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g.
zones 9-12 and zones 13-16). None of the zones assigned to a PC5108 module
may be used for wireless devices.

Program the PC5132-RS from a system keypad or using downloading software
on a remote computer (e.g. DLS-1). Read your system Installation Manual for
more information. Read this manual before you begin installing the PC5132-RS.

1.1 How to use this Manual

To install and set up the PC5132-RS and wireless devices, follow these steps:

1. Temporarily mount  and wire the PC5132-RS module (see 

Section 2)

2. Enroll and program wireless devices using zones (see 

Section 3)

3. Enroll and program wireless keys and handheld keypads (see 

Section 3)

4. Complete zone and other programming on the system (see 

Section 4)

5. Test the placement of all the wireless devices 

(see Section 5)

6. Permanently mount the PC5132-RS receiver and wireless devices 

(see

Section 5)

For information on troubles related to the PC5132-RS, see 

Section 6.

For help with troubleshooting, see 

Section 7.

1.2 Specifications and Features

• Current Draw: 130 mA
• Frequency: 922 to 926 MHz, Spread Spectrum
• Zones - receiver can receive signals from up to 32 wireless zones
• Antenna - orthogonal design for enhanced performance
• Supervisory - programmable supervisory window, one to 24 hours
• Location

- can be wired up to 750 ft. / 230 m from the main panel with 22 gauge wire
- connects to Keybus
- for longer wire runs, thicker gauge wire must be used.

• Compatibility: The PC5132-RS v3.0 can be connected to the following

panels:

 

PC5010, PC5015, PC5008, PC1565, PC585

S E C T I O N  1

Introduction

Summary of Contents for PC5008

































Reviews: