DSC Envoy NT9005EU, Installation & Programming Manual, Page: 30 / 60

Advanced Programming
26
16 Not Used
17 Away Armed Status - Both output types [17] and [18] are
designed to follow the status of the Stay/Away zones. If the
system is armed with Stay/Aways bypassed, the Stay output
should be active. If the system is armed with the Stay/Aways
active, the Away output should be active. Therefore, the fol-
lowing is how all arming techniques will work.
Default Attributes: 1,3 ON 2 OFF
STAY Key
*9 + Code
AWAY Key
Keyswitch Arm
*0 Quick Arm
Access Code Arm
DLS arm - Away
Auto-arm - Away
Stay armed, then *1 -
Stay
Stay
Away
Depends on Delay Type Zone
during the Exit Delay
Depends on Delay Type Zone
during the Exit Delay
Depends on Delay Type Zone
during the Exit Delay
Away
Away
Away
18 Stay Armed Status - See Away Armed Status Type [17]
Default Attributes:
1,3 ON 2 OFF
19 Command Output #1 [*][71] - When activated by entering
the [*][71] command, the PGM type will activate according
to how it is configured by its corresponding attributes.
Default Attributes: 1,3,4,5 ON 2 OFF
20 Command Output #2 [*][72] - When activated by entering
the [*][7][2] command, the PGM type will activate according
to how it is configured by its corresponding attributes.
Default Attributes: 1,3,4 ON 2,5 OFF
21 Command Output #3 [*][73] - When activated by entering
the [*][7][3] command, the PGM type will activate according
to how it is configured by its corresponding attributes.
Default Attributes: 1,3,4 ON 2,5 OFF
22 Command Output #4 [*][74] - When activated by entering
the [*][7][4] command, the PGM type will activate according
to how it is configured by its corresponding attributes.
Default Attributes: 1,3,4 ON 2,5 OFF
☞
If there are multiple outputs programmed with the same out-
put type, the output options must be the same.
23-24 Not Used
25
☞
Delayed Fire and Burglary Output - This programmable
output type operates the same as the Fire and Burglary Out-
put (Type 01), except it follows the Transmission Delay Timer
found in
section [370] . If a zone is violated that has the TX
Delay Attribute enabled (Bit 7), the Bell and Regular Fire and
Burg PGMs will activate. At the end of the Transmission
Delay, this PGM type will activate.
If a zone is violated that causes an alarm that does not have
Tx Delay enabled, these outputs will activate immediately.This
Output will activate for Audible Exit Fault
Default Attributes: 1,3 ON 2 OFF
[009] PGM Output Programming (PGM 1,2) NT9005
Default
PGM 1 19 I___I___I
PGM 2 10 I___I___I
☞
PGMs in this section must have the corresponding zone
in
section [30] set to [00]
[011] PGM Output Programming (PGM 11-14) NT9204
Default
PGM 11 01 I___I___I
PGM 12 01 I___I___I
PGM 13 01 I___I___I
PGM 14 01 I___I___I
☞
If this module is connected, then the outputs for the
PGMs in
section [009] become part of the Keybus con-
necting to this module. Refer to paragraph 2-3.
[012] Keypad Lockout Options
The system can be programmed to lock out keypads if a series
of incorrect access code entries is made. After the
Number of
Invalid Codes has been reached the system will lockout the
keypad for the Lockout Duration and log the event to the
event buffer. For the duration of the lock out, the system wil
sound an error tone when any key is pressed. The invalid code
counter will reset every hour. To disable Keypad Lockout, pro-
gram
Number of Invalid Codes as [000] (default).
Number of
Invalid Codes 000 I___I___I___I (000 - 255)
Lockout
Duration 000 I___I___I___I (000 - 255)
minutes
☞
If Keypad Lockout is active the system cannot be dis-
armed with a keyswitch.
[013] First System Option Codes
1 ON Hardwired Zones Normally Closed
All zones are wired as normally closed circuits between
Y1 or G2 terminals and the B terminal. The end-of-line
resistor is not required. An alarm will be generated when
the circuit is opened.
OFF Hardwired Zones use EOL Resistors
✓
All zones must be wired with an end-of-line resistor
between the
Y1 or G2 terminals and the B terminal. An
alarm will be generated when the circuit is opened or
shorted.
firealarmresources.com