3G Alarm Communicator Installation Manual
Ratings
7
R
ATINGS
H
ARDWARE
C
OMPATIBILITY
Note for ULC Listed installations:
Products or components of products, which perform communications functions only, shall comply with the requirements applicable to
communications equipment as specified in CAN/CSA –C22.2 No. 60950-1, Information Technology Equipment-Safety - Part 1: Gen-
eral Requirements. Where network interfaces, such as the following, are internal to the subscriber control unit or receiver, compliance
to CAN/CSA –C22.2 No. 60950-1 is adequate. Such components include, but are not limited to: Hubs; Routers; Network interface
devices; Third party communications service providers; Digital subscriber line (DSL) modems; and Cable modems.
Note for UL Listed installations:
Packet switched data network interface equipment, manufactured by other than the burglar alarm equipment manufacturer, that is not
required for the processing of the signals shall be evaluated to the applicable requirements of the Standard for Information Technology
Equipment – Safety – Part 1: General Requirements, UL 60950-1, either as burglar alarm equipment or communication equipment.
S
OFTWARE
C
OMPATABILITY
The Communicator is compatible with the following software:
• Connect24 Using: Simple Messaging System (SMS) Protocol.
• Connect24 Remote Flash. Using: Internet Protocol (IP) using Trivial File Transfer Protocol (TFTP).
C
ONNECT
24™
1
A
CCOUNT
AND
SIM
CARD
A
CTIVATION
(Before Installation)
Installation of the Communicator requires activation with Connect24 before operation. .
IMPORTANT:
Prior to installing a
3G2075
or
TL2753G
Communicator, you will require a Profile Number, Installer ID Number, and
an Installer Password. Perform the following pre installation:
1. Retrieve the installer account and password from the Aurora Technical Services (ATS) group.
2. Call VRU number 1-866-910-3865.
3. Follow the voice prompts to enter the required account information.
4. Power up the communicator. The Communicator will automatically connect and download its programming from Connect24 once
the unit is initialized.
NOTE:
Following initial installation, you can contact the ATS group to re-configure the Communicator remotely, using the account
created for this installation.
Before leaving the installation site, the Communicator 3G2075 or TL2753G shall be connected via an APPROVED (acceptable
to the local authorities) Network Interface Device (NID) (e.g., for UL Installations, UL60950 listed NID). All wiring shall be per-
formed according to the local electrical codes.
Table 3: Communictor Electrical Ratings
Model
3G2075
Cellular Only
TL2753G
Ethernet and Cellular
Power Supply Ratings
Input Voltage
3.5 / 3.9 / 4.2 VDC (min / NOM / MAX) from the SCW9055/SCW9057 panel
Current Consumption
75 mA
100 mA
Standby Current (@
3.7V)
75 mA
100 mA
Alarm (Transmitting) Current)
400 mA @ 3.7V during transmission
Antenna Specifications
Dual band Antenna
See Table 2
Environmental Specifications
Operating Temperature
0°C - 49°C (32°F- 120°F)
Humidity
5% ~ 85% relative humidity, non-condensing
Mechanical Specifications
Board Dimensions (mm)
109 x 110
Weight (grams)
60
65
Table 4: Compatibility
Communicator
Receiver/
ControlPanel
Description
3G2075
TL2753G
Receiver
SG System I, v1.14+
SG System II, v2.11+
SG-DRL3-IP, v2.3+
SG-DRL4-IP, v1.2+
Control Panel
SCW9055/SCW9057 V1.00
C
OMMUNICATOR
P
RE
I
NSTALLATION
C
ONFIGURATION
1.
Connect24
,
DSC
, and
DLS IV
are Registered Trademarks of Tyco International Ltd. and its respective Companies. All Rights Reserved.
Summary of Contents for 3G2075
Page 2: ......
