background image

34

Ethernet/Cellular Programming Worksheets

3G Alarm Communicator Installation Manual

[355] Partition 3 Label Default [Partition 3].
________________________________
[356] Partition 4 Label Default [Partition 4].
________________________________
[357] Partition 5 Label Default [Partition 5].
________________________________
[358] Partition 6 Label Default [Partition 6].
________________________________
[359] Partition 7 Label Default [Partition 7].
________________________________
[360] Partition 8 Label Default [Partition 8].
________________________________

User Label Programming

Programming is 16 character ASCII text

[361] User 1 Label Default [User 1].
________________________________
[362] User 2 Label Default [User 2].
________________________________
[363] User 3 Label Default [User 3].
________________________________
[364] User 4 Label Default [User 4].
________________________________
[365] User 5 Label Default [User 5].
________________________________
[366] User 6 Label Default [User 6].
________________________________
[367] User 7 Label Default [User 7].
________________________________
[368] User 8 Label Default [User 8].
________________________________
[369] User 9 Label Default [User 9].
________________________________
[370] User 10 Label Default [User 10].
________________________________
[371] User 11 Label Default [User 11].
________________________________
[372] User 12 Label Default [User 12].
________________________________
[373] User 13 Label Default [User 13].
________________________________
[374] User 14 Label Default [User 14.]
________________________________
[375] User 15 Label Default [User 15].
________________________________
[376] User 16 Label Default [User 16].
________________________________
[377] User 17 Label Default [User 17].
________________________________

[378] User 18 Label Default [User 18].
________________________________
[379] User 19 Label Default [User 19].
________________________________
[380] User 20 Label Default [User 20].
________________________________
[381] User 21 Label Default [User 21].
________________________________
[382] User 22 Label Default [User 22].
________________________________
[383] User 23 Label Default [User 23].
________________________________
[384] User 24 Label Default [User 24].
________________________________
[385] User 25 Label Default [User 25].
________________________________
[386] User 26 Label Default [User 26].
________________________________
[387] User 27 Label Default [User 27].
________________________________
[388] User 28 Label Default [User 28].
________________________________
[389] User 29 Label Default [User 29].
________________________________
[390] User 30 Label Default [User 30].
________________________________
[391] User 31 Label Default [User 31].
________________________________
[392] User 32 Label Default [User 32].
________________________________
[393] User 33 Label Default [User 33].
________________________________
[394] User 34 Label Default [User 34].
________________________________
[395] User 35 Label Default [User 35].
________________________________
[396] User 36 Label Default [User 36].
________________________________
[397] User 37 Label Default [User 37].
________________________________
[398] User 38 Label Default [User 38].
________________________________
[399] User 39 Label Default [User 39].
________________________________
[400] User 40 Label Default [User 40].
________________________________

Zone Label Programming

[401] Zone 1 Label Default [Zone 1].

Summary of Contents for 3G2060

















































Reviews: