background image

17

Ethernet/Cellular Programming Options

3G Alarm Communicator Installation Manual

[013] DLS Outgoing Port

Default (0BFA/3066)

The DLS Outgoing Port is used for outgoing session to DLS IV after an SMS request has been

sent to the Communicator. Use this Section to set the value of the local outgoing port. The value

must be changed if the Communicator is located behind a firewall and must be assigned a particu-

lar port number, as determined by your network administrator. In most cases, changing the default

value or configuring your firewall with this port is not required.  
Valid range: 0000-FFFF.

NOTE: 

If Section [006] Toggle Option [7] is ON, DLS will use the Primary path for session. If 

Section [006] Toggle Option [7] is OFF DLS will use the Ethernet path, if available.

[021] Account Code

Default (FFFFFF)

The account code is included when transmitting any events generated by the Communicator. (e.g.,

Panel Absent Trouble). It is recommended that the account code be the same as the control panel

account number. Valid range: 00000

1

-FFFFF

E

. If 4 digit account codes are needed the 2 lowest

digits shall be programmed as FF (e.g., Account 1234 is programmed as:1234

FF

).

NOTE: 

Programming this Section with all 0 or F will cause a Module Configuration Trouble.

NOTE: 

This section shall sync with Panel Option [310] with Panel version 4.50 or higher.

[022] Communications Format

Default (04)

Program 03 for Contact ID (CID). Program 04 for SIA. The module can be configured to send

Events in SIA or CID format. The SIA communication format follows the level 2 specifications of

the 

SIA Digital Communication Standard - October 1997

. This format will send the account code

along with its data transmission. The transmission will look similar to the following at the

receiver. 

NOTE: 

This section shall sync with panels version 4.50 or higher.

Example: 

Nri0 ET001 

where: 

N

 = New Event; 

ri0

 = Partition/Area identifier; 

ET

 = Panel Absent Trouble;

001

 = Zone 001.

Communications Reporting Codes

[023] Panel Absent Trouble

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with

the panel have been lost for more than 60 seconds.

[024] Panel Absent Trouble Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with

the control panel have resumed.

Table 10: Communications Reporting Codes

Event

SIA 

Identifier

SIA 

Reporting 

Code

CID

Qualifier

CID 

Event 

Code

CID 

Reporting 

Code

CID 

User/

Zone

[023] Panel Absent Trouble

ET

001

1

3

55

001

[024] Panel Absent Trouble Restore

ER

001

3

3

55

001

[025] Radio Activation Restore

RS

001

3

5

52

001

[026] Ethernet 1 Test Transmission

RP

001

1

6

A3

951

[027] Ethernet 2 Test Transmission

RP

002

1

6

A3

952

[028] Cellular 1 Test Transmission

RP

003

1

6

A3

955

[029] Cellular 2 Test Transmission

RP

004

1

6

A3

956

[030] FTC Restore

YK

001

3

3

54

001

Summary of Contents for 3G2060

















































Reviews: