manualshive.com logo in svg

DSC 3G2055, Installation Manual, Page: 24 / 52

Share
Download
DSC 3G2055 Installation Manual Download Page 24

24

C

OMMUNICATIONS

 R

EPORTING

 C

ODES

[023] Panel Absent Trouble

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when
communications with the panel have been lost for more than 60 seconds.

[024] Panel Absent Trouble Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when
communications with the control panel have resumed.

[025] Radio Activation Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur after any suc-
cessful Connect24 programming session.

S

YSTEM

 T

EST

 O

PTIONS

 [026 - 029]

Test Transmissions to Primary Receiver, with Backup to Secondary Receiver:

Set Ethernet Section [026] to (FF); [027] to (00). Set Cellular Section [028] to (FF); 
[029] to (00).

• If the test transmission fails to the primary receiver it will backup to the secondary

receiver.

• If the test transmission fails to the secondary receiver an FTC trouble will be

generated.

Test Transmission Unique to Primary and Secondary Receivers:

Set Ethernet Section [026] to (FF); [027] to (FF). Set Cellular Section [028] to (FF); 
[029] to (FF).

• The module will send periodic test transmissions to each receiver independently,

with no backups.

• If the test transmission fails to any of the programmed receivers, an FTC trouble

will be generated.

Alternate Test Transmission:

Alternate Test Transmission can be enabled or disabled in Section [005] Toggle Option
[7].

[026] Ethernet 1 Transmission

Default (FF)

Program 00 to disable this event transmission or FF to enable. See System Test
Options (above) for details on settings.

Table 9: Communications Reporting Codes

Event

SIA 

Identifier

SIA 

Reporting 

Code

CID

Qualifier

CID 

Event 

Code

CID 

Reporting 

Code

CID 

User/

Zone

[023] Panel Absent Trouble

ET

001

1

3

55

001

[024] Panel Absent Trouble 

Restore

ER

001

3

3

55

001

[025] Radio Activation 

Restore

RS

001

3

5

52

001

[026] Ethernet 1 Test Trans-

mission

RP

001

1

6

A3

951

[027] Ethernet 2 Test Trans-

mission

RP

002

1

6

A3

952

[028] Cellular 1 Test Trans-

mission

RP

003

1

6

A3

955

[029] Cellular 2 Test Trans-

mission

RP

004

1

6

A3

956

[030] FTC Restore

YK

001

3

3

54

001

Summary of Contents for 3G2055





















































Reviews:

No comments