manualshive.com logo in svg

DSC 3G2055, Installation Manual, Page: 11 / 52

Share
Download
DSC 3G2055 Installation Manual Download Page 11

11

I

NSTALLING

 CAT 5 C

ABLE

 (TL2553G 

ONLY

)

A Category 5 (CAT 5) ethernet cable must 
be run from a source with Ethernet/Inter-
net connectivity to the Communicator 
module, inside the Self Contained Wire-
less Control Panel cabinet. The Communi-
cator end of the cable must have an RJ-45 
plug, which connects to the Communica-
tor’s RJ-45 jack. All requirements for instal-
lation of CAT5 ethernet cable must be 
observed for correct operation of the Com-
municator, including, but not limited to, the 
following:

• Do NOT strip off cable sheathing more

than required for proper termination.

• Do NOT kink/knot cable.
• Do NOT crush cable with cable ties. 
• Do NOT untwist CAT5 pairs more than

1.2cm (½”).

• Do NOT splice cable.
• Do NOT bend cable at right angles or make any other sharp bends.

NOTE: CAT5 specification requires that any cable bend must have a minimum 5 cm (2 
in.) bend radius. Maximum length of CAT 5 cable is 100m (328 ft.).
NOTE: The Ethernet cable shall not be visible when the installation is complete 
unless the install is a surface mount installation.

I

NSERTING

/

R

EMOVING

 

THE

 SIM 

C

ARD

1. Remove the front

cover of the SCW
Control Panel to
access SIM  

card

holder.

2. Remove power from

the SCW and
disconnect the backup battery connections.

3. On the SIM card holder push gently to slide the cover towards OPEN as indicated

by the arrow on SIM holder. This will unlatch the SIM card holder on the side
furthest from edge of the Communicator. See Figure 1.

4. Lift up the SIM card holder from the side that is not hinged.

NOTE: The SIM card can be damaged  by bending or scratching contacts. Use caution 
when handling the SIM card.
5. Insert or remove the SIM card, noting the orientation of the notches on the SIM

card and the SIM card holder.

6. When inserting a SIM card, insert the card in the proper orientation and gently

push the SIM card holder down and slide the holder as indicated by the arrow on
SIM holder, to LOCK.

RJ-45 Connector

DG0009635

 Figure 2: RJ-45 Pinout

SIM Card Pinouts

DG0009396

 Figure 3: SIM Card Pinouts

Summary of Contents for 3G2055





















































Reviews:

No comments