manualshive.com logo in svg

Drone Amplified Ignis II, Operational Manual

Share
Download
Drone Amplified Ignis II Operational Manual Download Page 91

Ignis Operations Manual

Drone Amplified

7.8.5 Gremsy Gimbal Parameters

Figure 7.8.5: Gremsy Gimbal parameters

Touching the Gremsy Gimbal Parameters button from the Advanced configuration

screen will allow you to configure some settings of a Gremsy gimbal and view its firmware
version, as shown above. The options are:

Gimbal control configuration:

Settings for setting up a communication channel between

the app and the gimbal are saved on the flight controller. This is a shortcut to those in
case that's what you were looking for.

MOUNT_ORIENTATION message rate:

How frequently the gimbal should emit a MAVLink

message indicating its current orientation. We recommend 30 Hz so that the orientation
indicator overlaid on the video feed doesn't look choppy.

HEARTBEAT message rate:

This allows the flight controller to identify this as a gimbal,

otherwise it doesn't serve any purpose. We recommend 1 Hz.

SYS_STATUS message rate:

This message isn't useful. We recommend 0 Hz.

MOUNT_STATUS message rate:

This message isn't useful. We recommend 0 Hz.

RAW_IMU message rate:

This message isn't useful. We recommend 0 Hz.

Firmware version:

The version of the gimbal firmware. We recommend downgrading to

version 7.5.6. Version 7.5.8 has sluggish tuning. Do a gyro calibration in GTune after
downgrading.

Last Updated

Page 91

Apr 13, 2022

Summary of Contents for Ignis II











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands