Drivecon Crane Commander CCES102, Instruction Manual

Page: 54 / 57

CCES Series AC Drives for Crane use (50 Hz system)
Function List
CCES-SET (ver10-2).xls
CODE Function Function Description UNIT RANGE
50Hz Traverse
factory setting 50Hz Hoist
factory setting
NOTE
Customer
settings
F00 Factory adjustment Factory adjustment 000 000
F01 Accel time Accel time 0.1 sec 00.1~30.0 sec. 05.0 03.0 *1
F02 Decel time Decel time 0.1 sec 00.1~30.0 sec. 05.0 03.0 *1
F03 Creep / Top Divisor
Ratio of operating speed
when enabled
0.1 001~030 01.0 01.0 *1
F04 Motor rotation direction
Direction selection from
keypad. 0= Forward
1= Reverse
000~001 000 000 *1
F05 V/F pattern V/F pattern setting 1 001~004 001 001 *2
F06 Frequency upper limit Frequency upper limit 0.1 Hz 00.0-01.0~200 Hz 50.0 50.0 *2, *3
F07 Frequency lower limit Frequency lower limit 0.1 Hz 00.0-01.0~200 Hz 01.0 03.0 *3
F08 SP1 frequency SP1 frequency 0.1 Hz 00.0-01.0~200 Hz 06.0 06.0
*3
SP1 is operating
when FOR or REV
is active
F09 Current limit stall level Current limit level 1 000-025~150% 150 000
F10 Start / Stop control
0: Keypad
1: Terminal (TM2)
1 000~001 001 001
F11 Frequency control
0: Keypad
1: Terminal (0~10V /
0~20mA)
2: Terminal (4-20mA)
3: 1~3 preset speeds
4: 2 step infinitely
variable
5: 3 step infinitely
variable
1 000~005 003 003
F12 Carrier frequency control Carrier frequency setting 1 001~010 005 005
F13 Torque compensation
Torque compensation
gain
0.1% 00.0~10.0% 00.0 02.0 *1
F14 Stop method
0: Decelerate stop
1: Free run stop
1 000~001 000 001
F15 DC braking setting
DC braking time /
coasting start delay
0.1 sec 00.0~25.5 sec 00.5 01.0 *1
F16 DC braking setting
DC braking injection
frequency
0.1 Hz 01.0~10.0 Hz 01.5 00.0 *1
F17 DC braking setting DC braking level 0.1% 0.0~20.0% 08.0 00.0
F18
Electronic thermal
overload protection Protection base on
motor rated current.
1% 000-001~200% 100 100 *1
F19
Multifunction input
connection point
Multifunction input
terminal (SP1) function
TB1 #5
001 001
F20
Multifunction input
connection point
Multifunction input
terminal (reset) function
TB1 #6
001 001
F21 Multifunction output
Multifunction output
terminal
TB1 #1 and 2
001 004
F22 Current detect
Output current detect
level.
1% 005~150% 025 025 *1
F23 Frequency detect level
Output frequency detect
level. 1% hysteresis
1 01.0~200 01.0 03.0
F24 Auto restart
Number of Auto-restart
times
1 000~005 000 000
F25 Factory setting 000 000
F26 SP2 frequency SP2 frequency 0.1 Hz 00.0-01.0~200 Hz 25.0 25.0 *1
F27 SP3 frequency SP3 frequency 0.1 Hz 00.0-01.0~200 Hz 50.0 50.0 *1
F28 Voltage stall Voltage stall level control 0=OFF, 1=ON - 001 000
F29 Software version
F30 Fault log
001: SP2
002: Emergency stop. N/C
003: External base block. N/O
004: Reset
005: Creep input
006: Top limit
001: SP3
002: Emergency stop. N/C
003: External base block. N/O
004: Reset
005: Creep input
006: Top limit
Last 3 malfunction memory
001: Operating
002: Frequency reached
003: Fault
004: At current detect level
005: At frequency detect level
010: Constants initialization to 50 Hz system Traverse mode
011: Constants initialization to 50 Hz Hoist mode
020: Constants initialization to 60 Hz system Traverse mode
021: Constants initialization to 60 Hz Hoist mode
CPU program version
Notes:
*1: Setting can be changed during running mode.
*2: Please refer to F25.
*3: If the setting range is above 100, the setting unit becomes 1.
52
Rev. 1-1-01
ver. 10.2