85
T w o
p e r s o n
l i f t
r e q u i r e d .
L i f t i n g t h e
Dremel LC40 Laser Cutter alone may result
in personal injury.
Shipping the Dremel LC40
Laser Cutter
Refer to the unboxing section on page 14
of the manual for help in returning the
Dremel LC40 Laser Cutter to its original
packaging configuration.
1. Unplug and wind up the Power Cord.
2. Unplug the Hex Box™ connector cord.
3. Disconnect the Ethernet cable.
4. Disconnect the Air Tube.
5. Disconnect the exhaust duct.
6. Drain the cooling water. Place the Hex
Box™ in a suitable container to capture
the system water. Place the container in
a location below the Dremel LC40 Laser
Cutter. Remove the cap from the Water
Tank. Disconnect the clear inlet water
hose from the Hex Box™ and allow the
water to drain. This will drain the water
from both the Hex Box™ and the Laser
Tube. It is important to drain as much
water as possible in case of freezing
weather. Tilting the Hex Box™ back and
forth will help drain the water.
7. If shipping the Dremel LC40 Laser Cutter
i n i t s o r i g i n a l c a r t o n . R e m o v e t h e 4
screws securing the Exhaust Shroud and
place the Exhaust Shroud in its carton.
8. Remove the Honeycomb Plate and place
it in its package.
9. When placing the Dremel LC40 Laser
Cutter in its original carton try to replace
the foam pads in the order they came
o u t . I t i s i m p o r t a n t t h e f o a m p a d s
securely capture the Gantry system.
Secure the Gantry with plastic ties to
minimize any movement of the Gantry
during transportation.
10.
Return the Hex Box™ to its original
shipping location inside the Dremel
L C 4 0 L a s e r C u t t e r e n c l o s u r e . I f i t
cannot be placed inside, it must be
secured to the pallet outside of the
Dremel LC40 Laser Cutter.
11.
When shipping the Dremel LC40 Laser
Cutter the unit must be secured to a
pallet to prevent damage.
Storing the Dremel LC40
Laser Cutter
1. Unplug and wind up the Power Cord.
2. Unplug the Hex Box™ connector cord.
3. Disconnect the Ethernet cable.
4. Disconnect the Air Tube.
5. Disconnect the exhaust duct.
6. Drain the cooling water. Place the Hex
Box™ in a suitable container to capture
the system water. Place the container in
a location below the Dremel LC40 Laser
Cutter. Remove the cap from the Water
Tank. Disconnect the clear inlet water
hose from the Hex Box™ and allow the
water to drain. This will drain the water
from both the Hex Box™ and the Laser
Tube. It is important to drain as much
water as possible in case of freezing
weather. Tilting the Hex Box™ back and
forth will help drain the water.
7. S t o r e i n a c l e a n , d r y d u s t f r e e
environment within a temperature range
of 60-85 °F (16-29 °C). Keep the laser
covered to minimize dust build up inside
the Dremel LC40 Laser Cutter enclosure.
SHIPPING AND STORAGE
Observe all provided warnings and safety instructions prior to and
when using the Dremel LC40 Laser Cutter.
Failure to do so may
result in fire, equipment damage, property damage and/or personal injury, up to and
including death.
DM 1600A01CX8 08-18 LC40 EN.qxp_LC40 8/17/18 10:33 AM Page 85
