7
2 f
ilters are included.
To purchase replacement filters:
drbrownsbaby.com
WARRANTY
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase. Any defective part will be repaired or replaced at no
charge if it has not been tampered with and appliance has been used according to these
printed instructions. This warranty gives you specific legal rights as well as other rights
which vary from state to state.
This warranty does not cover a defect that has been caused by negligence, accidents or
improper use of the appliance. To keep your Dr. Brown’s™ Bottle Sterilizer and Dryer in
good condition and retain your warranty, USE ONLY AS DIRECTED.
CUSTOMER SERVICE
If you experience unsatisfactory operation or have any questions/comments,
call Handi-Craft’s Customer Service at 1-800-778-9001 or send an email to
[email protected].
For purchases made outside the United States and Canada, please contact your
local distributor.
REPLACING THE FILTER
CAUTION: Unplug from outlet and allow to cool for 60 minutes before
replacing filter.
Replace the filter every six months of regular use for optimal performance.
Follow the steps below:
1. The filter is located at the bottom of the base. Gently squeeze the latches on the filter
cover to remove it.
2. Remove and replace the filter, ensuring the pull tab is still visible on top of the filter.
3. Snap the filter cover back into position.
Note: Filter must always be used to ensure proper performance.
4
A
1
2
3
D
C
B
2
1
4
3
C
B
A
D
MATERIAL
FILTER REPLACEMENT
DO NOT SCALE DRAWING
SHEET 1 OF 1
SCALE: 1:1
REV.
DWG. NO.
C
SIZE
TITLE:
DRAWN
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
SOLIDWORKS
MFG/Q.A APPR.
ENG APPR.
THIS DRAWING AND RELATED 3D CAD DATA
CONTAINS PROPRIETARY INFORMATION
THAT ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
X
.X
.XX
.XXX
X
.X
2.5
0.5
0.25
0.13
0.5
0.25
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
INTERPET PER ASME Y14.5-1994
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
3D
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
THIRD ANGLE
PROJECTION
1
15JUL19
RBW
2
1
A
B
A
B
1
2
1
THIRD ANGLE
PROJECTION
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
3D
INTERPET PER ASME Y14.5-1994
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
NO PLACE:
ONE PLACE:
TWO PLACE:
THREE PLACE:
ANGLE:
ANGLE:
2.5
0.5
0.25
0.13
0.5
0.25
X
.X
.XX
.XXX
X
.X
THIS DRAWING AND RELATED 3D CAD DATA
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE PERMISSION
OF HANDI-CRAFT CO.
ENG APPR.
MFG/Q.A APPR.
SOLIDWORKS
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
DRAWN
TITLE:
SIZE
A
DWG. NO.
REV.
SCALE: 1:2
RBW
15JUL19
SHEET 1 OF 1
DO NOT SCALE DRAWING
FILTER AND COVER
MATERIAL
1
3
2
Summary of Contents for Natural Flow AC177
Page 24: ...WSP006 F2...
