Draytek VigorAP 800 User Manual Download Page 71

Page: 71 / 118

VigorAP 800 User’s Guide

Policy

Select to enable any one of the following policy or disable the
policy. Choose

Activate MAC address filter

to type in the

MAC addresses for other clients in the network manually.
Choose

Blocked WLAN from LAN

will separate all the

WLAN stations from LAN based on the MAC Address list.

MAC Address Filter

Display all MAC addresses that are edited before.

Client’s MAC Address

Manually enter the MAC address of wireless client.

Add

Add a new MAC address into the list.

Delete

Delete the selected MAC address in the list.

Edit

Edit the selected MAC address in the list.

Cancel

Give up the access control set up.

Click it to save the access control list.

Cancel

Clean all entries in the MAC address list.

Summary of Contents for VigorAP 800























































































































Search results

Summary of Contents for VigorAP 800

Reviews:

Related manuals for VigorAP 800

Brands by name

Popular brands

Draytek VigorAP 800, User Manual

Search results

Summary of Contents for VigorAP 800

Reviews:

Related manuals for VigorAP 800

Brands by name

Popular brands