Draytek VigorAP 800 User Manual Download Page 35

Page: 35 / 118

VigorAP 800 User’s Guide

Note:

The

Wireless LAN

settings will be changed according to the

Operation Mode

selected here. For the detailed information, please refer to the section of

Wireless LAN

Local Area Network (LAN) is a group of subnets regulated and ruled by modem.

Click

LAN

to open the LAN settings page and choose

General Setup

Note:

Such page will be changed according to the

Operation Mode

selected. The

following screen is obtained by choosing

as the operation mode.

IP Address

Type in private IP address for connecting to a local private
network (Default: 192.168.1.2).

Subnet Mask

Type in an address code that determines the size of the network.
(Default: 255.255.255.0/ 24)

DHCP Server
Configuration

DHCP stands for Dynamic Host Configuration Protocol. DHCP
server can automatically dispatch related IP settings to any local
user configured as a DHCP client.

Enable Server /
Disable Server

Enable Server lets the modem assign IP address to every host in
the LAN.

Disable Server lets you manually or use other DHCP server to
assign IP address to every host in the LAN.

Summary of Contents for VigorAP 800























































































































Search results

Summary of Contents for VigorAP 800

Reviews:

Related manuals for VigorAP 800

Brands by name

Popular brands

Draytek VigorAP 800, User Manual

Search results

Summary of Contents for VigorAP 800

Reviews:

Related manuals for VigorAP 800

Brands by name

Popular brands