Dräger Isolette 8000 plus Instructions For Use Manual Download Page 27 | Manualshive

Page: 27 / 30

Dräger Isolette 8000 plus Instructions For Use Manual Download Page 27

Supplement to the instructions for use

|

Isolette 8000 plus

27

Index

Index

A

Accessories

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . 7
Reprocessing . . . . . . . . . . . . . . . . . . . . . . . 7

Air inlet filter . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assembly

Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Condensation management . . . . . . . . . . . 20
Drain plug . . . . . . . . . . . . . . . . . . . . . . . . . 20
Gasket  . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Grommet. . . . . . . . . . . . . . . . . . . . . . . . . . 23
Heater/Impeller . . . . . . . . . . . . . . . . . . . . . 22
Iris port sleeves  . . . . . . . . . . . . . . . . . . . . 23
Manifold  . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Skin probe  . . . . . . . . . . . . . . . . . . . . . . . . 26
Water reservoir . . . . . . . . . . . . . . . . . . . . . 19

B

Bed

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . 7

C

Classification . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Disinfection . . . . . . . . . . . . . . . . . . . . . . . . 13
Machine . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cleaning agents. . . . . . . . . . . . . . . . . . . . . . . 17
Condensation management. . . . . . . . . . . . . . . 9

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 20

Controller

Reprocessing . . . . . . . . . . . . . . . . . . . . . . 15

Cuff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

D

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Accessories . . . . . . . . . . . . . . . . . . . . . . . . 7
Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Condensation management . . . . . . . . . . . . 9
Drain plug . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Impeller. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Water reservoir . . . . . . . . . . . . . . . . . . . . . 11

Disinfectant . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disinfectants . . . . . . . . . . . . . . . . . . . . . . . . . 17
Disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Machine . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Drain plug

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disassembly. . . . . . . . . . . . . . . . . . . . . . . . 9

F

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Filter chamber

Reprocessing . . . . . . . . . . . . . . . . . . . . . . 16

Filter cover

Reprocessing . . . . . . . . . . . . . . . . . . . . . . 16

G

Gasket

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 23

Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Grommet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 23

H

Heater

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disassembly. . . . . . . . . . . . . . . . . . . . . . . . 8
Reprocessing . . . . . . . . . . . . . . . . . . . . . . 16

Hood

Reprocessing . . . . . . . . . . . . . . . . . . . . . . 15

Humidity

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

I

Impeller

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disassembly. . . . . . . . . . . . . . . . . . . . . . . . 8
Reprocessing . . . . . . . . . . . . . . . . . . . . . . 16

Iris port

Sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Iris port sleeves

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 23

M

Machine cleaning . . . . . . . . . . . . . . . . . . 13, 16
Manifold

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disassembly. . . . . . . . . . . . . . . . . . . . . . . 10

«
...
25
26
27
28
29
...
»

Summary of Contents for Isolette 8000 plus































Reviews:

No comments