manualshive.com logo in svg

Dräger Isolette 8000 plus, Instructions For Use Manual, Page: 22 / 30

Share
Download
Dräger Isolette 8000 plus Instructions For Use Manual Download Page 22

22 

 Supplement to the instructions for use

  |  

Isolette 8000 plus

  

Reprocessing

Fitting the heater radiator and fan impeller

1. On devices without the humidification system option, install the impeller (A) onto 

the motor shaft.

2. Install the heater radiator (B).
3. On devices without the humidification system option, install the heater/impeller 

cover (C).

4. On devices with the humidification system option, install the heater/impeller 

cover (D) and the duct cover (E).

WARNING

Risk of death or serious injury

Using older software versions can lead to incorrect operation of the humidification 
system leading to injury.

►

The humidification system with the heater/impeller cover with duct cover must 
be used with software version 5.n or higher.

Fitting the scale and the bed and related components

NOTICE

Risk of damage to the device

The hood contains 4 tabs (one at each corner) which keep the deck securely in 
place. Installing the upper cover when the hood is down may result in damage to 
the upper cover and/or jamming of the hood in place.

►

Ensure that the hood is raised before attempting to install the upper cover.

48252

C

D

E

B

A

Summary of Contents for Isolette 8000 plus































Reviews:

No comments