background image

NOTE: Place enough sifted earth into the pool area to 
cover the pressure pads. With a high groundwater level 
(in ground pool) we advise to install a concrete floor.

INSTALL WALL JOINTS

Step 11

The wall joints overlap (see plan). If joint piece doesn't 
slide on easily, correct the side supports until the joints 
fit perfectly. See to it that the round shape is preserved. 
Connect the wall joints by means of the bolts and 
screws included in the packaging. Attention: the 
screwhead must be on the inside of the pool. Smooth 
the screws. Fix the protective strip with tape.

INSTALL VERTICALS & END CAPS

Step 12

Install the verticals, so that the screw aperture is at 
the front side on top of the vertical. The construction 
is connect by screws. Position vertical end cap over 
vertical (see plan). 

A drop of oil on the screws 

facilitates your work.

INSTALL BOTTOM RAILS

Step 9

Slide the bottom rails into the vertical end caps, groove 
up (see plan). Start on opposite sides of the side vertical 
assemblies with the end rails stamped with 12". When 
the bottom condition is not optimal, place a patio block 
under every vertical end cap (sunk on bottom level for 
extra certainty).

INSTALL WALL

Step 10

Remove steel pool wall from carton. Note ‘Up’ arrow on 
wall. Determine starting point of wall from preliminary 
planning, depending on the place of the pump and the 
filter. The skimmer opening will be at the inside end of 
the wall coil. Always start with the center of a vertical 
end cap. Always uncoil 1,5 m and insert bottom edge 
into groove in bottom rails. When the ends of the pool 
do not connect completely, correct this by telescope the 
bottom rail more or less into the vertical end caps. 

A S S E M B L Y   I N S T R U C T I O N S   S U N L A K E   -   O V A L   -   P A G E  8

Only for 16" and 21" pools, 

stamped TR (4 pcs)

Bottom rails stamped 12", 

16", 18" and 21"

Level

Bottom rails

Bottom rail 

connector

Optional sunk patio 

blocks

steel pool wall

large dia  

stabilizer rail

start wall at center of vertical 

end cap

sifted 

earth

large and small 

stabilizer rails telescoped   

     around ends of 

         pool only

Screw

Bolt  

stabilizer rails

vertical end cap

vertical

Summary of Contents for SUNLAKE Series





















Reviews: