background image

M O N T A G E   I N S T R U C T I E   C E N T U R Y   -   P A G I N A   1

A S S E M B L Y   I N S T R U C T I O N S   S U N L A K E   -   O V A L   -   P A G E   2 0

PREPARING FOR WINTER

When the swimming season is over, you have to follow 
the instructions to get your pool ready for winter.

ATTENTION!

 Do not remove all the water from your 

pool and also do not remove the liner. An empty pool can 
namely cause pool failure.

Lower the water level

-  Lower the water level in your pool so that it is approxi-

mately 6” (15 cm) below the inlet fixture; maintain this 
water level by checking it regularly.

-  If you have a skimmer, then absolutely do not let the 

water freeze in the skimmer but rather drain this water.

Check all screws and connections

-  Make sure that all installation connections and parts 

are positioned correctly and that the pool wall is not 
moved away from the bottom rails.

-  Make also sure that all connections are water tight.

Check if there is rust

-  Correct all damages or rust spots with a varnish stick.

Check the liner (interior tarpaulin)

-  Make sure that the top of the liner is still overhanging 

the pool wall attached to the plastic edge. Do not 
remove the liner from your pool. Upon removal of the 
liner of the pool the warrantee becomes void. Do not 
pump dry all the water from the pool during the winter.

Leaks found

-  Make sure that there aren’t any leaks in the liner. 

Leaks during the winter can cause serious damages to 
your pool.

Pool accessories

-  Remove all pool accessories from the pool, including 

the ladder. Leave the skimmer and inlet fixture in 
place.

 

The filter

-  Disconnect the filter from your pool and follow the filter 

instructions for maintaining the filter during the winter. 
Clean the pump and the filter for the winter (frost free).

Anti-freeze liquid

This liquid can be used without problems in combination 
with chloride products. Upon finding algae present first 
apply a ‘shock treatment.’ The liquid should be, dis-
solved in a pail of water, spread out equally across the 
water surface. During the dosage the pump should be 
in operation. The dosage is 0.5 litres per 10 m

3

, after 

approximately four weeks 0.3 litres per 10 m

3

.

ATTENTION!

 Never mix the liquid with other pool che-

micals or chemicals and always add the product to 
water, never the other way around.

If you do not adhere closely to the winter instructions, 
the warrantee of your pool may become void. Thus care-
fully adhere to all instructions for maintaining your pool 
during the winter.

Summary of Contents for SUNLAKE Series





















Reviews: