Doro 850 colour Manual Download Page 9

Page: 9 / 44

English

www.doro.com

English

www.doro.com

Installation

The display

Indicator

Function

Shown within range of the base unit. Flashes when out of range.

INT

Intercom call

Ringer off (with

Indicates that a handset is in use.

Monitor/hands free function.

New SMS messages received/network voicemail.

Alarm function activated.

Battery charge indicator

INT 1

Handset number, for use with more than one handset.

Base 1

Base unit number, for use with more than one base unit.

Describes the function of the button shown below the display, eg

Menu or Redial.

Press 19

Key Lock

Please note:

To conserve battery power the display will be darken after approximately 20 seconds while on a

call and when placing the handset on the base unit. To briefly illuminate the display, press

��

��

�

�� 

Summary of Contents for 850 colour













































Search results

Summary of Contents for 850 colour

Reviews:

Related manuals for 850 colour

Brands by name

Popular brands

Doro 850 colour, Manual

Search results

Summary of Contents for 850 colour

Reviews:

Related manuals for 850 colour

Brands by name

Popular brands