manualshive.com logo in svg

Dorner iDrive 3200 Series, Installation, Maintenance & Parts Manual

Share
Download
Dorner iDrive 3200 Series Installation, Maintenance & Parts Manual Download Page 9

851-702 Rev. A

9

Dorner Mfg. Corp.

3200 Series iDrive Belt Conveyors

Installation

Wiring

The 3200 series iDrive is available in 3 models:
• Cover Mounted Controls with 115 volt Power Supply
• Cover Mounted Controls with Customer Provided Power

Supply

• Customer Wired with Flying Leads

Cover Mounted Controls with 115 volt 
Power Supply

1. No wiring is required. Attach quick disconnect end of 

power supply to power jack 

(Figure 19, item 1)

.

 Figure 19

 Figure 19           

2. See “Change Acceleration / Deceleration Settings” on 

page 11 for changing factory control settings.

Cover Mounted Controls with Customer 
Provided Power Supply

1. Locate the male disconnect plug provided.
2. Wire and solder DC power to the two terminals of the 

provided DC power plug. Wire +VDC to the short lug 

(Figure 20, item 1) 

and -VDC to the long lug 

(Figure 

20, item 2)

.

 Figure 20

 Figure 20           

3. Required power is 36VDC, 4 amps minimum.
4. See “Change Acceleration / Deceleration Settings” on 

page 11 for changing factory control settings.

A

 WARNING

Exposed moving parts can cause severe 
injury. LOCK OUT POWER before removing 
guards or performing maintenance.

A

 WARNING

Exposed moving parts can cause severe 
injury. LOCK OUT POWER before removing 
guards or performing maintenance.

1

A

 WARNING

Exposed moving parts can cause severe 
injury. LOCK OUT POWER before removing 
guards or performing maintenance.

2

1

Summary of Contents for iDrive 3200 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands