manualshive.com logo in svg

Dorner iDrive 3200 Series, Installation, Maintenance & Parts Manual

Share
Download
Dorner iDrive 3200 Series Installation, Maintenance & Parts Manual Download Page 3

851-702 Rev. A

3

Dorner Mfg. Corp.

3200 Series iDrive Belt Conveyors

Introduction

Upon receipt of shipment:
• Compare shipment with packing slip. Contact factory

regarding discrepancies.

• Inspect packages for shipping damage. Contact carrier

regarding damage.

• Accessories may be shipped loose. See accessory instruc-

tions for installation.

Dorner’s Limited Warranty applies.
Dorner 3200 series conveyors are covered by Patent 

Numbers 5,156,260, 6,871,737B2, 6,910,571B1, 

6,971,509B2, and corresponding patents and patent 

applications in other countries.
Dorner reserves the right to make changes at any time 

without notice or obligation.
Dorner has convenient, pre

−

configured kits of Key Service 

Parts for all conveyor products. These time saving kits are 

easy to order, designed for fast installation, and guarantee 

you will have what you need when you need it. Key Parts 

and Kits are marked in the Service Parts section of this 

manual with the Performance Parts Kits logo

.

Warnings 

−

 General Safety

IMPORTANT

Some illustrations may show guards removed. 
DO NOT operate equipment without guards.

A

 WARNING

The safety alert symbol, black triangle with 
white exclamation, is used to alert you to 
potential personal injury hazards. 

A

 DANGER

Climbing, sitting, walking or riding on 
conveyor will cause severe injury. KEEP OFF 
CONVEYORS.

A

 DANGER

DO NOT OPERATE CONVEYORS IN AN 
EXPLOSIVE ENVIRONMENT.

A

 WARNING

Exposed moving parts can cause severe 
injury. LOCK OUT POWER before removing 
guards or performing maintenance.

A

 WARNING

Gearmotors may be HOT.

DO NOT TOUCH Gearmotors.

A

 WARNING

Dorner cannot control the physical 
installation and application of conveyors. 
Taking protective measures is the 
responsibility of the user.

When conveyors are used in conjunction 
with other equipment or as part of a multiple 
conveyor system, CHECK FOR POTENTIAL 
PINCH POINTS and other mechanical 
hazards before system start-up.

A

 WARNING

Loosening stand height or angle adjustment 
screws may cause conveyor sections to drop 
down, causing severe injury.

SUPPORT CONVEYOR SECTIONS PRIOR TO 
LOOSENING STAND HEIGHT OR ANGLE 
ADJUSTMENT SCREWS.

Summary of Contents for iDrive 3200 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands