60
Crane 4000LE
07-2022
RL6002-001
Crane 4000LE Installation Manual
In-ground Motion Assist 360 drive and speed control
Remote control enclosure
Chapter 13
13.6 Assemble Motion Assist 360 drive to mounting plate
Fig. 13.6.1 Drive with (8) M8 x 20 mm SHCS
1
(8)
2
Art.Nr
.: 34050001
150
100 - 240V ~ 50/60 Hz
-40 - +60°C
5
3
5
4
0
DIN 18650
Made in Germany
DORMA
D
eutschland GmbH
Dorma Platz 1
58256 Ennepetal
Germany
IP20
month year
System:
Speed Limiter:
Positioning
A
utomatic:
Static force:
Servomatic: Static force:
Automatic: Static force:
58 W
8 W
150 N
67 N
58 W
67 N
1/2/3
0
102 W
KT
FLEX
Dir
ec
t driv
e sy
st
em
Fig. 13.6.2 M8 x 20 mm and M8 x 30 mm SHCS
WARNING
Use caution when lifting and positioning
Motion Assist 360 drive!
13.6.1 Remove six M8 SHCS.
Drive is shipped from factory with eight M8 x 20 mm
SHCS installed.
1. Remove six of the eight M8 x 20 SHCS leaving
two M8 x 20 SHCS at 180 degrees to each other
(Fig. 12.6.3).
TIPS AND RECOMMENDATIONS
Use socket wrench with 6 mm hex key socket.
13.6.2 Install
drive
flange.
1. Install drive flange on drive using six M8 x 30 mm
SHCS.
13.6.3 Check tightening torque on M8 SHCS.
1. Use torque wrench to check tightening torque on
the eight M8 SHCS.
WARNING
Danger from incorrect screw tightening torque!
If drive flange mounting screws are tightened
with an incorrect tightening torque, components
may detach causing injuries and material
damage.
• Never exceed the maximum specified screw
tightening torque.
• Contact dormakaba for further information.
13.6.4 Maximum screw tightening torque.
Screw diameter
Maximum permissible screw
tightening torque
M8
15.5 Nm
10 ft-lb
Fig. 13.6.4
Drive flange
3
2
Art.Nr
.: 34050001
150
100 - 240V ~ 50/60 Hz
-40 - +60°C
5
3
5
4
0
DIN 18650
Made in Germany
DORMA
D
eutschland GmbH
Dorma Platz 1
58256 Ennepetal
Germany
IP20
month year
System:
Speed Limiter:
Positioning
Automatic:
Static force:
Servomatic: Static force:
Automatic: Static force:
58 W
8 W
150 N
67 N
58 W
67 N
1/2/3
0
102 W
KT
FLEX
Dir
ect driv
e sy
st
em
2
2
Fig. 13.6.3 Drive with (2) M8 x 20 mm SHCS
Fig. 13.6.5 Drive flange installed
1
RX6010-001
Motion Assist 360 drive
2
RF6003-01C
M8 x 20 mm hex bolt
3
RF6003-02C
M8 x 30 mm SHCS black oxide
4
RC6025
Drive flange, 4" OD
Table 13.6.1
Motion Assist 360 drive and drive flange
hardware
4
Art.Nr
.: 34050001
150
100 - 240V ~ 50/60 Hz
-40 - +60°C
5
3
5
4
0
DIN 18650
Made in Germany
DORMA
D
eutschland GmbH
Dorma Platz 1
58256 Ennepetal
Germany
IP20
month year
System:
Speed Limiter:
Positioning
Automatic:
Static force:
Servomatic: Static force:
Automatic: Static force:
58 W
8 W
150 N
67 N
58 W
67 N
1/2/3
0
102 W
KT
FLEX
Dir
ect driv
e sy
st
em
4
(6)
3
1
2
2
