Dormakaba 660 Series Installation Instructions Manual Download Page 24

Page: 24 / 40

79/RT/E7900/770/E-760/660 Series

PK3678_T 04-18

9 Installation of Mechanical Override Models

6. Verify the attachment of the lever handle

CAUTION

WARNING

IMPORTANT

To verify that the lever handle has been correctly attached

to the housing:

10. Remove key (N)

11. Insert a small flat screwdriver (tool T, page 18) into the

hole on the underside of the lever handle (H) and push

inthe lever catch (F) see fig 10A.

12. Pull on the lever handle (H).

You should not be able to remove the lever handle (H). If

it comes off of the housing, you did not assemble the lock

correctly. Return to steps 2, 3, 4 & 5 and make sure that

the lever (H) looks like Fig. 10 and repeat this verification

process. (Step 6)

Fig. 10A

(T) Small screwdriver

or equivalent tool

(H)

6a. Adjust the lever feel
If applicable, to reduce the lever play, using the 5/64 allen

key (P1), tighten the set screw (O1) while pushing the lever

against the front housing. Make sure the lever rotates

properly after tighting the set screw (O1) See fig 10B.

Fig. 10B

7. Test the movement of the lever handle

(remove the key (N) in cylinder (J))

13. Turn the handle (H) clockwise (for a right-handed lock) or

counter-clockwise (for a left-handed lock)

14. Release the handle (H) slowly. It should return freely to

its horizontal position. (Fig.11)

Fig. 11

(H)

Cylinder

(J)

8. Test the mechanical override function (Complete all

tests in Section 4, pages 13 & 14 after lock is assembled
on the door)

CAUTION

WARNING

IMPORTANT

This test can only be performed when the lock is not affixed

to the door.

15. Without using the key (N), turn the lever handle (H)

clockwise (for Right-handed locks) or counter-clockwise

(for Left-handed locks). The inside drive hub (B) should

not rotate when the handle (H) turns. (Fig. 12)

Fig. 12

(B) inside drive hub

does not move

(H)

16. With the lever handle (H) in the horizontal position, insert

the key (N) into the cylinder (J) and turn it clockwise until

it stops. (This applies to both Right and Left-handed

locks, see Fig.13)

Fig. 13

(H)

(M)

17. Let go of the key (N), and again turn the lever handle (H)

clockwise (for Right-handed locks) or counter-clockwise

(for Left-handed locks). Now the inside drive hub (B)

should rotate in the same direction as the lever handle

(H) when it is turned. (Fig. 14)

Fig. 14

(B) inside drive

hub rotates

Summary of Contents for 660 Series









































Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands

Dormakaba 660 Series, Installation Instructions Manual

Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands