Dormakaba 660 Series Installation Instructions Manual Download Page 14

Page: 14 / 40

79/RT/E7900/770/E-760/660 Series

PK3678_T 04-18

CAUTION

WARNING

IMPORTANT

Perform the following procedures in order, with the door

OPEN unless otherwise indicated.

Inside Lever:
Turn the inside lever downward. The latch bolt retracts fully.

If the lever or the thumbturn feels tight (hard to turn or does

not return easily to its horizontal position), check the align-

ment of the lock assemblies. Loosen the mounting screws

and shift the inside trim assembly slightly until the friction is

eliminated. If the problem persists check the position of the

holes on the door (compared to the mortise).

Standard Deadbolt:
Turn the thumbturn back and forth. The deadbolt extends

and retracts fully and without undue friction.

Turn the thumbturn to extend the deadbolt again then turn

the inside lever. The deadbolt and the latch bolt retract si-

multaneously and fully without undue friction.

Optional Autodeadbolt:
Press and hold the auxiliary bolt (D5). The deadbolt (D3) will

extend. Keep the auxiliary bolt depressed, and turn the in-

side lever all the way down and hold it there. The latch (D4)

and deadbolt retract together.

Release the auxiliary bolt (D5), then let the inside lever re-

turn to a horizontal position. The deadbolt will remain re-

tracted while the latch will extend.

Outside Lever:
Turn the outside lever downward. The latch bolt does not

retract.

If the latch bolt retracts, verify that the batteries are prop-

erly installed.

If the lever feels tight (hard to turn, or does not return easily

to its horizontal position), ensure the square spindle is not

too long.

Electronics and Card Reader: E-760/770/79 Series Only (for

660 Series, see Step 7 Page 16)

Test the lock’s response to keycards: a Test keycard, a Grand

Master keycard, and an Emergency keycard. For 760 and

770 insert keycards as shown, with the magnetic stripe fac-

ing toward the door and to the left. For 79 Series, present

card to reader.

A. Test the Lock Before Programming (E-760/770/790/79

Series) (E7900 see command card)

Normal Entry: Verify that the deadbolt is retracted. Use the

Test keycard in the reader. The red and green LEDs each

flash once and then the green LED flashes for four seconds.

For 79 Series, present card to reader.

Turn the outside lever downward while the green LED is

flashing. The latch retracts fully. Release the lever then turn

it again after the LED stops flashing. The latch must not

retract after the LED stops flashing without first inserting

the keycard.

Privacy Switch: Turn the thumbturn to the horizontal posi-

tion. (On autodeadbolt models, first extend the deadbolt by

pressing the auxiliary latch (D5). On storeroom locks, skip

this test.) Use the Test keycard in the reader but do not turn

the lever. Instead of the normal sequence of indicator lights

you should see the following: the red and green LEDs each

flash once and then the green LED flashes once, followed

by the red LED flashing continuously for four seconds. If you

see the flashing green LED there is a problem with the pri-

vacy switch.

B. Lock Programming (E-760/770/79 Series) (E7900 see

command card)

Program the lock with its room number (FDU User Guide).

(For ALTLAS, see ATLAS User Guide. For multihousing, refer

to RezShield user guide).

Verify that the deadbolt is retracted, and use the Grand

Master keycard with the reader. The green LED flashes for

4 seconds. Turn the outside lever downward while the green

LED is flashing. The latch retracts fully. Release the lever

then turn it again after the LED stops flashing. The latch

must not retract after the LED stops flashing without first

inserting the keycard.

4 Lock Testing (E-760/770/79 Series only)

for mechanical override, see Step 8 Page 23 / For RT lock series, please refer to system 6000 manual.

Summary of Contents for 660 Series









































Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands

Dormakaba 660 Series, Installation Instructions Manual

Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands