Dormakaba 660 Series Installation Instructions Manual Download Page 9

Page: 9 / 40

79/RT/E7900/770/E-760/660 Series

PK3678_T 04-18 9

3 Installation of Standard ASM or ESM Models

3.2 Install the Strike
1. Align the paper template on the door frame at the desired

handle height (

), and along the vertical center line of

the mortise (CL), which is also the center line of the door

edge, allowing for any bumpers on the door frame.

CAUTION

WARNING

IMPORTANT

Respect applicable building codes regarding handle height.

NOTE: that the centerline of an ESM mortise does

NOT pass through the screw holes on the strike.

(CL)

2. Mark the locations of the dust box cutout and mounting

screws for the strike.

3. Mortise the door frame to receive the dust box, and drill

the pilot holes for the mounting screws (dimensions and

depths marked on template).

4. Position the strike against the doorframe and align it with

the mounting screw holes. Trace the outline of the strike.

5. Remove material from within the strike outline so that

the strike will be flush with the doorframe.

6. For ASM, install the dust box (optional for wood door

frames, required for metal door frames), and check the

strike handing on the template. Install the strike using the

screws provided. Use wood screws for wood frame and

mechined screws for steel frames.

CAUTION

WARNING

IMPORTANT

When strike is installed on wood frames under one inch

thick, wood screws supplied are not adequate. use screws

of efficient lenght to engage the structural stud behind the

frame. Use only the strike and dust box supplied. Use of non-

approved parts may void the warranty.

Summary of Contents for 660 Series









































Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands

Dormakaba 660 Series, Installation Instructions Manual

Search results

Summary of Contents for 660 Series

Reviews:

Related manuals for 660 Series

Brands by name

Popular brands