manualshive.com logo in svg

Doosan L6-60HA-T4F, Operation And Maintenance Manual

Share
Download
Doosan L6-60HA-T4F Operation And Maintenance Manual Download Page 25

Operating Instructions

Operating & Maintenance Manual

25

LS Operating Controls and Instruments

1.

Hourmeter:

 Records cumulative engine operating hours for maintenance purposes.

2.

Fuel Level Gauge (Optional):

 Indicates fuel level in tank.

3.

Rotary Switch with Key:

 Positions (left to right) for all lamp circuits and panel

receptacles.

4.

Preheat Position:

 Place rotary switch in Preheat position for 5 seconds. Move switch

to START position.

PREHEAT

 - Energizes Glow Plug in engine manifold to assist starting.

RUN 

- Normal engine operating position.

OFF

 - Shuts down engine.

START

 - Energizes engine cranking motor.

5.

Main Breaker: 

25 amp for all lamp circuits and panel receptacles.

6.

Switch: 

Lamp 1

7.

Switch: 

Lamp 2

8.

Switch: 

Lamp 3

9.

Switch: 

Lamp 4

10.

Twist-Loc Receptacle

: 240V 25 Amp

120V

240V

1

2

3

4

54462353

4

3

2

1

5

10

7

8

9

Summary of Contents for L6-60HA-T4F



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands