manualshive.com logo in svg

Doosan L6-60HA-T4F, Operation And Maintenance Manual

Share
Download
Doosan L6-60HA-T4F Operation And Maintenance Manual Download Page 23

Operating Instructions

Operating & Maintenance Manual

23

L6 Operating Instructions

L6 Operating Controls and Instruments

The operating controls and instruments are arranged on the control panel as shown above. A 
description of each panel device is as follows:

1.

Hourmeter:

 Records cumulative engine operating hours for maintenance purposes.

2.

Fuel Level Gauge (Optional):

 Indicates fuel level in tank.

3.

Rotary Switch with Key:

 Positions (left to right).

PREHEAT 

- Energizes Glow Plug in engine manifold to assist starting.

OFF

 - Shuts down engine.

RUN 

- Normal engine operating position.

START

 - Energizes engine cranking motor.

4.

Preheat Position:

 Place rotary switch in Preheat position for 5 seconds. Move switch

to START position.

5.

Main Breaker:

 25 amp for all lamp circuits and panel receptacles.

6.

Switches:

 For standard lamps 1 thru 4.

7.

Switches

: 

For standard lamps 1 thru 4.

8.

Switches

: For standard lamps 1 thru 4.

9.

Switches:

 For standard lamps 1 thru 4.

10.

Push to Reset Breaker:

 For receptacle (Item 11).

11.

Receptacle:

 120 Volt 20 amp.

12.

Receptacle:

 240 Volt 20 amp.

HOURMETER

FUEL LEVEL

LAMP

LAMP

LAMP

LAMP

PRE
HEAT

OFF

RUN

START

1

2

5

10

6

7

8

9

3

4

11

12

36847655

Summary of Contents for L6-60HA-T4F



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands