manualshive.com logo in svg

Doosan L6-60HA-T4F, Operation And Maintenance Manual

Share
Download
Doosan L6-60HA-T4F Operation And Maintenance Manual Download Page 24

Operating & Maintenance Manual

Operating Instructions

24

  

L8 Operating Instructions 

L8 Operating Controls and Instruments

The operating controls and instruments are arranged on the control panel as shown above. A 
description of each panel device is as follows:

1.

Panel Light:

 Illuminates when activated by TOGGLE SWITCH.

2.

Toggle Switch:

 Activates PANEL LIGHT above ON and OFF.

3.

Hourmeter:

 Records cumulative engine operating hours for maintenance purposes.

4.

Fuel Level Gauge (Optional):

 Indicates fuel level in tank.

5.

Rotary Switch with Key:

 25 amp for all lamp circuits and panel receptacles.

PREHEAT

 - Energizes Glow Plug in engine manifold to assist starting.

RUN 

- Normal engine operating position.

OFF

 - Shuts down engine.

START

 - Energizes engine cranking motor.

6.

Preheat Position:

 Place rotary switch in Preheat position for 5 seconds. Move switch

to START position.

7.

Main Breaker: 

35 amp for all lamp circuits and panel receptacles.

8.

Switch (Breaker): 

For standard lamps 1 thru 4.

9.

Switch: 

For standard lamps 1 thru 4.

10.

Switch: 

For standard lamps 1 thru 4.

11.

Switch: 

For standard lamps 1 thru 4.

12. thru 13. 

8kW Option Only: 

Switches (Breakers) - for lamps 5 and 6.

15. thru 16. 

Switches:

 Push to reset.

17. thru 18. 

Receptacle:

 120 volt 20 amp

.

HOURMETER

FUEL LEVEL

LAMP

PRE
HEAT

OFF

RUN

START

3

4

5

6

17

14

36514297

8

15

7

OFF

ON

2

9

10

11

12

13

1

LAMP

2

LAMP

3

LAMP

41

LAMP

5

LAMP

6

16

18

1

Summary of Contents for L6-60HA-T4F



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands