background image

Installation, Operation and Maintenance manual

6

DFPRE 4 Dust Collectors

 The access door requires tools to open. To avoid danger from rotating fan 

impellor, ensure fan is isolated and allow sufficient time for fan to become 

stationary.

  Do not put lit cigarettes or any burning object into the hood or ducting of any 

dust collection system.

  Compressed air is recommended for collectors that operate using reverse 

jet cleaning. Alternative gases should be assessed before use to ensure that 

explosive atmospheres are not introduced during media cleaning.

 Care should be taken to ensure that any potentially explosive atmosphere 

is not present when performing operations that increase the risk of ignition 

(opening of controller for adjustment or electrical repair for example). Ensure 

the installation is always returned to its original state.

  All electrical equipment should comply with a category according to EN 60079-0.

  The DFPRE 4 dust collector is designed for handling non-explosive dusts.

  Where applicable, equipment connected to the dust collector (for example, 

a cyclone) should be protected, using suitable isolation devices, against the 

transfer of flame and pressure if, in the event of an explosion initiating inside the 

dust collector, the connected equipment is not capable of safely withstanding 

these effects.

  None of the fan assemblies can be considered to be a fully sealed design, 

indeed most are arranged with either an open inlet or an open outlet. For this 

reason, the internal and external atmospheres can be considered the same 

in terms of any potentially hazardous classification.

 Standard fan assemblies should not exceed 3000 rpm (50 Hz supply) on 

systems fitted with an inverter drive.

  The filtration media is suitable for filtering particulate only (and not gas).

  Some applications are prone to risk of fire. This risk can be reduced by pulse 

cleaning and emptying the dust container regularly.
• 

Any extinguishing technique and material used must be suitable for the 

flammable nature of the dust.

• 

A water sprinkler system can be fitted as a special option.

 

Materials handled by the dust collector may be hazardous (e.g. toxic). Conduct 

a Risk Assessment to ensure correct technique is employed.

Summary of Contents for DFPRE 4 Series




























Reviews: