background image

Installation, Operation and Maintenance manual

22

DFPRE 4 Dust Collectors

Fan assembly removal

  Isolate electrical power supply.

1.  Open clean air chamber access door.
2.  Disconnect electrical cables from terminal box.
3.  Remove fan securing bolts.
4.  Remove airflow damper panel or fan box from top of collector, if applicable.
5.  The fan assembly can now be removed using a suitable lifting arrangement.

Dismantle / decomission dust collector

  Make sure to empty dust container and cover all the open areas to prevent 

possible dust spillage/exposure during transportation.

  Refer to general guidance lifting.

If it is intended, for any reason, to put the machine out of service and demolish it, 

some basic rules must be observed to safeguard health and the environment in 

which we live:
•  Sheaths, flexible ducts and components made of plastic or non-metal must be 

removed and disposed of separately.

•  Electrical components switches, power supplies, boards, etc., must be removed 

in order to be reused if they are still in good condition, or if possible, reconditioned 

and recycled.

•  However, the structure and all metal parts of the machine must be removed 

and grouped by type of material. The various parts obtained in this way can then 

be scrapped and melted down to allow the material that makes up the original 

machinery to be recycled.

The responsibility to reuse some machine parts, such as engines, lies solely with 

the User.
The manufacturer will not be held responsible for damage caused by the machine 

when it is used without certain components or by using it for purposes not expressly 

specified in this manual.
For the demolition of any machines connected to this machine, it is necessary to 

follow the instructions contained in the relevant user manuals.
IT IS NECESSARY TO RESPECT REGULATIONS IN FORCE IN THE COUNTRY OF THE 

USER REGARDING DISPOSAL OF THE MATERIALS PROVIDED WITH THE MACHINE.

Summary of Contents for DFPRE 4 Series




























Reviews: