background image

Installation, Operation and Maintenance manual

27

DFPRE 4 Dust Collectors

Description

Part number

Torit-Tex

®

 Earthed

CARTRIDGE DFE TORIT-TEX OD (349 X 349) MM X L 660 MM 

TRIAGONAL EARTHED

2627286E-000-440

Torit-Tex

®

 Anti-Static

CARTRIDGE DFE TORIT-TEX ANTI-STATIC OD (349 X 349) MM X 

L660 MM TRIAGONAL

2627287-000-440

Ultra-Web

® 

No Liner

DFE ULTRA-WEB NL CARTRIDGE (349 MM X 349 MM) OD X 660 

MM L (13.74" X 13.74") OD X 26" L

P034302-016-436

Ultra-Web

®

 Flame Retardant No Liner

DFE ULTRA-WEB FR NL CARTRIDGE (349 MM X 349 MM) OD X 

660 MM L (13.74" X 13.74") OD X 26" L)

P034304-016-436

Ultra-Web

®

 Stainless Steel

DFE ULTRA-WEB SS CARTRIDGE (349 MM X 349 MM) OD X 660 

MM L (13.74" X 13.74") OD X 26" L)

P034305-016-436

Fibra-Web

®

DFE FIBRA-WEB CARTRIDGE (349 MM X 349 MM) OD X 660 MM 

L (13.74" X 13.74") OD X 26" L)

P034306-016-431

Fibra-Web

®

 Earthed

DFE FIBRA-WEB EARTHED CARTRIDGE (349 MM X 349 MM) OD X 

660 MM L (13.74" X 13.74") OD X 26" L

P034306E-016-431

Fibra-Web

®

 Flame Retardant

DFE FIBRA-WEB FR CARTRIDGE (349 MM X 349 MM) OD X 660 

MM L (13.74" X 13.74") OD X 26" L)

P034307-016-431

Thermo-Web

®

DFE THERMO-WEB CARTRIDGE (349 MM X 349 MM) OD X 660 

MM L (13.74" X 13.74") OD X 26" L)

P034308-016-429

Thermo-Web

®

 Earthed

DFE THERMO-WEB EARTHED CARTRIDGE (349 MM X 349 MM) 

OD X 660 MM L (13.74" X 13.74") OD X 26" L

P034308E-016-429

Kevlar Nomex (high temp)

DFE HIGH TEMP CARTRIDGE (349 MM X 349 MM) OD X 660 MM L 

(13.74" X 13.74") OD X 26" L)

P034311-016-340

Sealable bag (for dirty cartridge)

2622217-000-440

Fan assembly

VCM 403S fan assembly (including motor

), 2.2 kW, 230V/400V, 50Hz 

AM0569800

VCM 451S fan assembly (including motor

), 3.0 kW, 230V/400V, 50Hz 

AM0569900

ART 452 fan assembly (including motor

), 4.0 kW, 400V/690V, 50Hz 

AM0573400

ART 451 fan assembly (including motor

), 5.5 kW, 400V/690V, 50Hz 

AM0570100

FQ 351 fan assembly (including motor

), 3 kW, 400V/690V, 60Hz 

2629243

VCM 401S fan assembly (including motor

), 3 kW, 400V/690V, 60Hz

2629244

ART 402 fan assembly (including motor

), 3.5 kW, 400V/690V, 60Hz 

2629245

ART 401 fan assembly (including motor

), 4.6 kW, 400V/690V, 60Hz 

AD1000431

VCM 501 fan assembly (including motor

), 7.5 kW, 400V/690V, 60Hz

AM1200601

 For other types/specifications/motors for hazardous areas consult Donaldson 

Access door assembly

Gasket Prik 5004

GASKET PRIK 5004 EPDM SHEET THICKNESS 1 MM TO 

3.5 MM 10 M-PACK

2622569X-000-440

 

Gasket 10 x 5 mm Neoprene

07011636

Dust container assembly

Polythene bag liner (for dust container with pressure balance)

AD1000279-000-440

Controller

For controller spares information refer to Publication DOCAM0097301

Compressed air assembly

Diaphragm valve – item not illustrated

DIAPHRAGM VALVE 25 MM (1”) THREADED CONNECTION 

INTEGRATED SOLENOID REMOTE PILOT

2620139

Diaphragm valve service kit – item not 

illustrated

REPAIR KIT FOR 25 MM (1”) DIAPHRAGM VALVE

2620087

 

Recommended spares for up to two years’ operation

Damaged safety related parts and safety components should be replaced only

with genuine original spare parts otherwise CE mark will become invalid

Summary of Contents for DFPRE 4 Series




























Reviews: