background image

Installation, Operation and Maintenance manual

26

DFPRE 4 Dust Collectors

TABLE 4 – STANDARD FAN MOTOR SUPPLY VOLTAGE DETAILS

To comply with European standards the motor nameplate will display the 

following:

3 Phase / 50 Hz (IEC 60034-30)

kW

Nameplate details

Range

0.75 – 3.0

230/3/50 D

220-240 D

400/3/50 Y

380-420 Y

4.0 and above

400/3/50 D

380-420 D

690/3/50 Y

660-690 Y

3 Phase / 60 Hz*

kW

Nameplate details

Range

0.75 – 3.0

250-280/3/60 D

250-280 D

440-480/3/60 Y

440-480 Y

4.0 and above

440-480/3/60 D

440-480 D

*Some motors will be fitted with a second nameplate displaying 60 Hz details

 The details above may not apply to non-standard motors.

SPARE PARTS LIST

Description

Part number

Filter cartridge assembly

Ultra-Web

®

CARTRIDGE DFE ULTRA-WEB OD (349 X 349) MM X L 660 MM 

TRIAGONAL

2626827-000-440

Ultra-Web

®

 Earthed

CARTRIDGE DFE ULTRA-WEB OD (349 X 349) MM X L 660 MM 

TRIAGONAL EARTHED

2626827E-000-440

Ultra-Web

®

 Flame Retardant

CARTRIDGE DFE ULTRA-WEB FR OD (349 X 349) MM X L 660 MM 

TRIAGONAL

2626913-000-440

Ultra-Web

®

 Flame Retardant Earthed

CARTRIDGE DFE ULTRA-WEB FR OD (349 X 349) MM X L 660 MM 

TRIAGONAL EARTHED

2626913E-000-440

Ultra-Web

®

 on SpunBond

CARTRIDGE DFE ULTRA-WEB SB OD (349 X 349) MM X L 660 MM 

TRIAGONAL

2626915-000-440

Ultra-Web

®

 on SpunBond Earthed

CARTRIDGE DFE ULTRA-WEB SB OD (349 X 349) MM X L 660 MM 

TRIAGONAL EARTHED

2626915E-000-440

Ultra-Web

®

 on SpunBond Anti-Static

CARTRIDGE DFE ULTRA-WEB SB ANTI-STATIC OD (349 X 349) MM 

X L 660 MM TRIAGONAL

2627283-000-440

Ultra-Web

®

 Anti-Static

CARTRIDGE DFE ULTRA-WEB ANTI-STATIC FR OD (349 X 349) MM 

X L660 MM TRIAGONAL

2627284-000-440

Torit-Tex

®

CARTRIDGE DFE TORIT-TEX OD (349 X 349) MM X L 660 MM 

TRIAGONAL

2627286-000-440

 

Recommended spares for up to two years’ operation

Damaged safety related parts and safety components should be replaced only

with genuine original spare parts otherwise CE mark will become invalid

Summary of Contents for DFPRE 4 Series




























Reviews: