Dodge Grand Caravan 2014 Owner'S Manual Download Page 30

Page: 30 / 682

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical

latch at the top of the RKE transmitter sideways with
your thumb and then pull the key out with your other
hand.

2. Insert the tip of the emergency key or a #2 flat blade

screwdriver into the slot and gently pry the two halves
of the RKE transmitter apart. Make sure not to damage
the seal during removal.

Emergency Key Removal

Remove Screw From Transmitter Case

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for Grand Caravan 2014











































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Grand Caravan 2014

Reviews:

Related manuals for Grand Caravan 2014

Brands by name

Popular brands

Dodge Grand Caravan 2014, Owner'S Manual

Search results

Summary of Contents for Grand Caravan 2014

Reviews:

Related manuals for Grand Caravan 2014

Brands by name

Popular brands