Dodge Grand Caravan 2014 Owner'S Manual Download Page 317 | Manualshive

Page: 317 / 682

background image

In this case, the light will remain on until the condition
has been corrected. If the problem is related to the brake
booster, the ABS pump will run when applying the brake
and a brake pedal pulsation may be felt during each stop.

The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is
indicated by the Brake Warning Light, which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers, which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed.
It will take longer to stop the vehicle. You could have
a collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System
(ABS), are also equipped with Electronic Brake Force
Distribution (EBD). In the event of an EBD failure, the
Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

315

«
...
315
316
317
318
319
...
»

Summary of Contents for Grand Caravan 2014











































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Grand Caravan 2014

Brand: Jeda Pages: 8

Brand: Jeep Pages: 496

Brand: Carefree Pages: 12

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: tams elektronik Pages: 19

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Quadratec Pages: 14

Brand: MAcarbon Pages: 3

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Brand: ADS Pages: 25

Brand: Prorack Pages: 13

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: Istar Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands