Dodge Grand Caravan 2014 Owner'S Manual Download Page 237 | Manualshive

Page: 237 / 682

background image

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions, and you
could lose control and have an accident. Do not use
Electronic Speed Control in heavy traffic or on roads
that are winding, icy, snow-covered or slippery.

PARKSENSE® REAR PARK ASSIST — IF
EQUIPPED

The ParkSense® Rear Park Assist system provides visual
and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to “ParkSense® Sys-
tem Usage Precautions” for limitations of this system and
recommendations.

ParkSense® will retain the last system state (enabled or
disabled) from the last ignition cycle when the ignition is
changed to the ON/RUN position.

ParkSense® can be active only when the shift lever is in
REVERSE. If ParkSense® is enabled at this shift lever
position, the system will remain active until the vehicle
speed is increased to approximately 11 mph (18 km/h) or
above. The system will become active again if the vehicle
speed is decreased to speeds less than approximately
10 mph (16 km/h).

ParkSense® Sensors

The four ParkSense® sensors, located in the rear fascia/
bumper, monitor the area behind the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 in (30 cm) up to 59 in
(150 cm) from the rear fascia/bumper in the horizontal
direction, depending on the location, type and orienta-
tion of the obstacle.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

235

«
...
235
236
237
238
239
...
»

Summary of Contents for Grand Caravan 2014











































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Grand Caravan 2014

Brand: Hama Pages: 2

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: Chevrolet Pages: 2

Brand: Icom Pages: 20

Brand: Prorack Pages: 20

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Paccar Pages: 63

Brand: Volvo Pages: 123

PRIME DESIGN VCR-TC11B

Brand: Safe Fleet Pages: 12

Dodge Caravan 2002

Brand: Chrysler Pages: 2399

Brand: Ednet Pages: 6

Brand: Edelbrock Pages: 4

IREESE TACTICAL 70894

Brand: Horizon Global Pages: 3

Brand: FALCON RIDGE Pages: 5

Brand: Honda Pages: 552

Brand: Dakota Digital Pages: 2

Brand: Philips Pages: 2

Actyon Sports II 2012.01

Brand: SSANGYONG Pages: 719

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands